Home>DIY RC Drone Accessories>VTX>Welding Combo for Mobula7 Frsky Upgrade Crazybee F3 Pro Flight Controller + Caddx 1200TVL FPV Camera Switchable VTX + Canopy V2
Welding Combo for Mobula7 Frsky Upgrade Crazybee F3 Pro Flight Controller + Caddx 1200TVL FPV Camera Switchable VTX + Canopy V2

Welding Combo for Mobula7 Frsky Upgrade Crazybee F3 Pro Flight Controller + Caddx 1200TVL FPV Camera Switchable VTX + Canopy V2 Item NO.: F26255-B//F26255-D/F26255-E

5.0
(1)
Write a Review
US$ 43.66
US$ 51.37 Save US$ 7.71 (15% Off)
Sold Out

Copy and share this link on social network or send it to your friends

Copy
Product Name Welding Combo for Mobula7 Frsky Upgrade Crazybee F3 Pro Flight Controller + Caddx 1200TVL FPV Camera Switchable VTX + Canopy V2
Item NO. F26255-B//F26255-D/F26255-E
Weight 0.077 kg = 0.1698 lb = 2.7161 oz
Category DIY RC Drone Accessories > VTX
Brand JMT
Creation Time 2019-03-04


Welding Combo for Mobula7 Frsky Upgrade Crazybee F3 Pro Flight Controller + Caddx 1200TVL FPV Camera Switchable VTX + Canopy V2

There are 4 kinds of Combo Kit optional, The electronic parts are well welded and tested. Please choose the version you request.

This listing is for Frsky, if you request other flight controller, Please feel free to message us.


Warm Tips: Buyers can directly replace for using when you receive these item,It saves buyers' time. In addition, because the solder joints of these electronic parts are very fine, after welding and testing by our professional technicians, the after-sales problems are avoided to some extent. Please use them with confidence. These products do not require an additional welding fee. If the customer does not need to weld, please leave us a message ,Thanks

Package include: (Standard combo)

1 x Crazybee F3 PRO flight controller for Frsky

1 x 5V Buzzer Alarm Beeper

1 x 5.8G 40CH 25MW Transmitter 700 TVL 120 degree CMOS Wide Angle NTSC FPV Camera

1 x Camera Cover Adjustable Canopy Protective Shell Black

1 x Battery Holder Protection Seat Black TPU 3D Printing

1 x Relative Cables

Package include: (Basic combo)

1 x Crazybee F3 PRO flight controller for Frsky

1 x 5V Buzzer Alarm Beeper

1 x 5.8G 40CH 25MW Transmitter 700 TVL 120 degree CMOS Wide Angle NTSC FPV Camera

1 x Battery Holder Protection Seat Black TPU 3D Printing

 


Package include: (Canopy Upgrade combo)

1 x Crazybee F3 PRO flight controller for Frsky

1 x 5V Buzzer Alarm Beeper

1 x 5.8G 40CH 25MW Transmitter 700 TVL 120 degree CMOS Wide Angle NTSC FPV Camera

1 x Camera Cover Canopy Protective Shell Red

1 x Battery Holder Protection Seat Black TPU 3D Printing

1 x Relative Cables



Package include: (Camera Upgrade combo)

1 x Crazybee F3 PRO flight controller for Frsky

1 x 5V Buzzer Alarm Beeper

1 x Caddx.us Turbo EOS2 1200TVL 2.1mm 1/3 CMOS Mini FPV Camera
1 x 5.8g 40ch 25mw~200mw switchable VTX

1 x Camera Angle adjustable Canopy V2 Red

1 x Battery Holder Protection Seat Black TPU 3D Printing

1 x Relative Cables

Crazybee F3 Pro Flight Controller Item Name: Crazybee F3 Pro FC
MCU: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 1-2S battery input (DC 3.5-8.7V)

Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Receiver ( Diffirent version having diffirent receiver)
Built-in Betaflight OSD(SPI Control)
Built-in Current meter Max 28A
Current meter scale set to 1175
Built-in 5V 1A BEC with LC filter

Built-in voltage detection
BLHELI_S pass-through Ready
Heading LED Ready

Firmware
(Frsky version) CRAZYBEEF3 PRO FR Firmware target: CrazybeeF3FR
(Flysky version) CRAZYBEEF3 PRO FS Firmware target: CrazybeeF3FS
(DSM-2/DSM-X version) CRAZYBEEF3 PRO Firmware target: CrazybeeF3DX
(Frsky EU-LBT version) CRAZYBEEF3 PRO FS Firmware target: CrazybeeF3FS
 
Onboard 5A 4 In 1 ESC

Power supply: 1-2S LiPo/LiPo HV (3.5v/8.7v)
MCU upgraded to EFM8BB21
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: S_H_50_REV16_7
Default protocol: DSHOT600

Onboard Frsky NON-EU receiver Version
SPI BUS receiver
Frsky D8/D16 switchable
Compatible Non EU transmitter both D8 and D16 mode

Channels: 8ch or 16ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
 
Onboard Frsky EU-LBT Version
(External XM+ receiver)
 

Operating Voltage Range: 3.7~10V
Operating Current: 30mA @5V
Operating Range: Full range
With RSSI output on board: Analog 0~3.3V
Firmware Upgradeable, Default firmware EU-LBT with RSSI

Onboard Flysky receiver Version
SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
 

Onboard DSM-2 / DSM-X receiver version

Serial bus receiver
Protocol: DSM-2/DSM-X compatible
Channels:6-9 (Depend on your radio)
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
 
Canopy
3 Kinds are optional
CADDX Turtle V2 Camera
Image sensor: 1/2.7" CMOS sensor
Horizontal: 800TVL
TV system: NTSC/PAL changeable
Video Resolution: 1080P@60fps / 1080P@30fps / 720@60fps
Power Input: DC 4.5-20V
FPV FOV: 155°
Recording FOV: 170°
Mini Illumination: 0.01lux
Image Resolution: 2 Megapixels
Lens: 1.8mm Turbo Eye Lens
Working Current: 380mA@5V/160mA@12V (low consumption)
OSD Menu: Yes (Support Voltage Display)
Video Files: MP4
Audio: Support
Electronic Shutter : PAL : 1/50-100,000 NTSC : 1/60-100,100
S/N Ratio: >60dB (AGC OFF)
Video Output: CVBS
Max Micro SD Card Supported: 8-64GB(need Class 10 or above, recommend Class 10/UHS-I/UHS-II)
Color: Red 
VTX

2019-05-10

C****s

Works fine and cheap.
The caddx has a really nice image quality