DUMBORC X6FG X6F X6DC X6DCG G 2.4G 6CH Receiver with Gyro for RC DUMBORC X6 X4 X5 Transmitter Remote Controller

Copy and share this link on social network or send it to your friends

Copy

DUMBORC X6FG X6F X6DC X6DCG G 2.4G 6CH Receiver with Gyro for RC DUMBORC X6 X4 X5 Transmitter Remote Controller Item NO.: F43396-D1 F43396-D2 F43397-D1 F43397-D2

Write a Review
US$ 5.97 (5% Off)
US$ 6.28 Save US$ 0.31
Version:
X6F X6FG with Gyro X6DC X6DCG with Gyro
Quantity:
Shipping Cost:
Estimate Shipping Cost

Product Name DUMBORC X6FG X6F X6DC X6DCG G 2.4G 6CH Receiver with Gyro for RC DUMBORC X6 X4 X5 Transmitter Remote Controller
Item NO. F43396-D1 F43396-D2 F43397-D1 F43397-D2
Weight 0.033 kg = 0.0728 lb = 1.1640 oz
Category DIY RC Drone Accessories > Receiver
Brand DumboRC
Creation Time 2021-03-24

DUMBORC X6FG X6F X6DC X6DCG G 2.4G 6CH Receiver with Gyro for RC DUMBORC X6 X4 X5 Transmitter Remote Controller


Specifications:
Item Brand:DUMBORC
Item Number:X6F/X6FG
X6F : without Gyro
X6FG : with Gyro
Item Name:Receiver
Material:plastic and electronic components
Model:Car/boat/tank
Modulation Mode: GFSK
Spread Spectrum: FHSS
Control Distance: More than 400 meters
Voltage Range:3.3-10V
Working Current:30mA
Compatible with:x4 x5 X6 Transmitter
The wiring diagram of the mixed control mode, there are 2 motors on the car, and the steering is through the differential speed.

Code
Each transmitter has an independent ID code. Before using the device, the receiver must pair with the transmitter. After the code is completed, the ID code is stored in the receiver, and there is no need to check the code again. When you buy a new X6FG receiver, you must re-code, otherwise the receiver will not work normally.
1. Put the transmitter and receiver together within 30-50CM.
2. Turn on the transmitter power switch. The X6F receiver will search for the nearest remote controller to perform code matching.
3. Press the (ID SET) switch on the side of the receiver for more than 1 second, the LED light flashes, indicating the start of code matching.
4. When the indicator light stops flashing, the code matching is completed.
5. Please confirm that your steering gear can be operated according to the transmitter.

Receiver antenna installation
1. Try to keep the antenna as straight as possible, otherwise the effective control range will be reduced.
2. Large model machines may have metal parts that affect signal transmission. In this case, the antennas should be on both sides of the model. In this way, the best signal state can be maintained in any posture.
3. The antenna should be as far away as possible from metal conductors and carbon fibers, at least half an inch away, but not excessively bent.
4. Keep the antenna as far away as possible from motors, electronic speed regulators (ESC) and other possible sources of interference.
5. In the process of actually installing the receiver, you can use sponge or foam material to wrap it up to prevent shocks.
6. The receiver contains some high-precision electronic components. Therefore, when using it, please handle it carefully to prevent severe vibration or high temperature environment.
7. In order to better protect the receiver, wrap it with anti-vibration materials such as R/C special foam or rubber cloth. In order to prevent the receiver from getting wet, it is best to put it in a plastic bag and seal the bag. If moisture enters the receiver, it may cause intermittent loss of control or even complete loss of control. Putting the receiver in a plastic bag can also prevent fuel and debris from entering the fuselage.

Warning: After the connection procedure is completed, please turn off the transmitter and turn it on again, and the procedure will take effect to confirm that the receiver is indeed connected to the transmitter normally and is under the control of the transmitter. When the power cord of the motor is connected to the governor, or when the engine is working, do not perform the connection procedure. Operation at this time may cause serious injury.

No related record found

You May Also Like