iFlight Chimera7 HD FPV Racing Drone 320mm 7inch 6S LR Drone with Air Unit for DJI, BNF with SucceX-D F7 V2.1 50A Stack 2806.5 1300KV/1800KV Motor
PRODUCT DESCRIPTION
Introducing what has been requested for too long already! A super efficient iFlight 7inch Long-Range bird that can go where you couldn't go before and can carry bigger batteries to get the flight time to surf the swiss alps if you want! Super stiff frame for minimum resonance and 2806.5 motors for maximum 7inch prop control. Fly big batteries top-mounted, or even bigger batteries bottom-mounted, 6cells recommended or 5cells for slow cruising. But whatever style you fly, a Lipo or Lion pack will just do the job. Recommended 5S 3.000mAh above (slow cruising) or 6S 2.500mAh above.
GPS functionality to find your way back and Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behaviour; Setup instructions included). Vertical and horizontal TBS Crossfire antenna mounts included to cover you and your antenna dead ends just in case.
HIGHLIGHTS:
- 6mm rigid arm design for more stiffness
- Top- and bottom battery mount option
- XING 2806.5 efficient wide stator motors
- GPS pre-installed for more safety at distance
- TPU bottom stand for GoPro ( protector for GoPro not included)
- 360° TPU protection, cam protection and antenna mounts for DJI
- FPV Air Unit for DJI, buttery-smooth 720p\120fps FPV feed (TPU soft mounted)
- No props in view (Air unit for DJI record in 1080p/60fps)
- Battery voltage LED status light (illuminated IF logo on the bottom
FRAME // ：Chimera7
- Wheelbase: 320mm
- Main body dimension: 258*199mm
- Bottom to top distance: 20mm
- Arm thickness: 6mm
- Bottom plate thickness: 3mm
- Top plate thickness: 2mm
- Upper(middle) plate thickness: 3mm
- Camera plate thickness: 3mm (included TPU inserts)
ELECTRONICS // SucceX-D F7 V2.1 Stack (50A 4-in-1 ESC)：
SucceX-D F7 V2.1 TwinG
- MCU: 216MHz STM32F722
- Gyro：2x ICM20689
- Baro: YES
- Blackbox：32MB
- Betaflight OSD: YES
- BEC: 5V 2.5A / 9V 2.5A
- Current sensor scale: 100
- Inverter for SBUS input (UART2-RX)
- Smartaudio & Tramp VTX protocol supported
- Beeper pad : Yes
- RSSI input pad: No
- UARTs：5
- Motor outputs: 8
- 8 pin 4in1 ESC port (GND, VBAT, M1, M2, M3, M4, CUR, R5)
- 6 pin Air Unit port for DJI (R1, GND, R2, T2, GND, 9V)
- BLHeli32 Telemetry：RX5
- Input voltage：recommended 2-6S, MAX 8S
- Firmware Target: IFLIGHT_F722_TWING
- Mounting pattern: 30.5*30.5mm φ4mm with Grommets φ3mm
- Dimensions: 36*36mm
- Weight: 7.5g
- USB type-C
ESC // SucceX 50A
- MCU: STM32F051
- Up tp 48kHz PWM frequency
- Capacitance: 470uF/50V
- Current Sensor: Yes
- Input: 2-6S LIPO
- Constant: 50A / Burst: 60A
- BlHeli32 telemetry: Yes
- BEC: No
- Supports up to Dshot1200, Proshot, Oneshot, Multishot
- Target: iFlight-BL32-4IN1
- Weight: 14.4g
- Mounting pattern: 30.5*30.5mm/Φ3mm
- Dimensions: 43*39mm (including the power pads)
BNF // Parts list (Build)
Prebuilt and indoor tested Quadcopter
- 1x Chimera7 frame
- 1x TPU bottom stand incl. lock screw for GoPro
- 1x FPV camera for DJI
- 1x FPV Air Unit Module for DJI
- 2x Albatross LHCP RP-SMA 5.8g 150mm antenna
- 2 sets x Gemfan tri-blade 7040 props (Set of 4 - Color may vary)
- 4x 20*250mm Microfiber PU Leather Battery Strap (Color May Vary)
Additional Suggested Parts (not included)
- Adjustable mount for GoPro (0-40)
- 1300KV Cruiser, suggested battery: 6S 4000mAh
- 1800KV Speed Cruiser, suggested battery: 6S 2600m
No related record found