iFlight Chimera7 Analog 6S Drone with Camera 320mm 7inch LR FPV Drone BNF with SucceX-D F7 V2.1 TwinG FC Built-in 50A ESC 2806.5 MotorPRODUCT
DESCRIPTION
Introducing what has been requested for too long already! A super efficient iFlight 7inch Long-Range bird that can go where you couldn't go before and can carry bigger batteries to get the flight time to surf the swiss alps if you want! Super stiff frame for minimum resonance and 2806.5 motors for maximum 7inch prop control. Fly big batteries top-mounted, or even bigger batteries bottom-mounted, 6cells recommended or 5cells for slow cruising. But whatever style you fly, a Lipo or Lion pack will just do the job. Recommended 5S 3.000mAh above (slow cruising) or 6S 2.500mAh above.?
GPS functionality to find your way back and Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behaviour; Setup instructions included). Vertical and horizontal TBS Crossfire antenna mounts included to cover you and your antenna dead ends just in case.?
HIGHLIGHTS:
- 6mm rigid arm design for more stiffness
- Top- and bottom battery mount option
- XING 2806.5 efficient wide stator motors
- GPS pre-installed for more safety at distance
- 800mW high power adjustable VTX
- 360¡ø TPU protection, FPV cam protection and antenna mounts
- Battery voltage LED status light (illuminated IF logo on the bottom)
FRAME //: Chimera7
- Wheelbase: 320mm
- Main body dimension: 258*199mm
- Bottom to top distance: 20mm
- Arm thickness: 6mm
- Bottom plate thickness: 3mm
- Top plate thickness: 2mm
- Upper(middle) plate thickness: 3mm
- Camera plate thickness: 3mm (included TPU inserts)
?
ELECTRONICS // SucceX-D F7 V2.1 Stack (50A 4-in-1 ESC)£º
SucceX-D F7 V2.1 TwinG
- MCU: 216MHz STM32F722
- Gyro£º2x ICM20689
- Baro: YES
- Blackbox£º32MB
- Betaflight OSD: YES
- BEC: 5V 2.5A / 9V 2.5A
- Current sensor scale: ?100
- Inverter for SBUS input (UART2-RX)
- Smartaudio & Tramp VTX protocol supported
- Beeper pad : Yes
- RSSI input pad: No
- UARTs£º5
- Motor outputs: 8
- 8 pin 4in1 ESC port (GND, VBAT, M1, M2, M3, M4, CUR, R5)
- BLHeli32 Telemetry£ºRX5
- Input voltage£ºrecommended 2-6S, MAX 8S
- Firmware Target: ? IFLIGHT_F722_TWING
- Mounting pattern: 30.5*30.5mm ©Ù4mm with Grommets ©Ù3mm
- Dimensions: ? 36*36mm
- Weight: 7.5g
- USB type-C
ESC // SucceX 50A
- MCU: STM32F051
- Up tp 48kHz PWM frequency
- Capacitance: 470uF/50V
- Current Sensor: Yes
- Input: 2-6S LIPO
- Constant: 50A / Burst: 60A
- BlHeli32 telemetry: Yes
- BEC: No
- Supports up to Dshot1200, Proshot, Oneshot, Multishot?
- Target: iFlight-BL32-4IN1
- Weight: 14.4g
- Mounting pattern: 30.5*30.5mm/©ß3mm
- Dimensions: 43*39mm (including the power pads)
VTX// SucceX Force 5.8GHz 800mW VTX Adjustable
- Item: SucceX-Force 800mW adjustable VTX
- Input voltage: 7-36V
- Output voltage/ Max current: 5V 1A
- 12V input current: 40mA@PIT MODE, 95mA@25mW, 185mA@100mW£¬250mA@400mW, 380mA@800mW
- Channel: 40
- size:36*36*3mm
- PIT/25mW/100mW/400mW/800mW
BNF // Parts list (Build)
Prebuilt and indoor tested Quadcopter
- 1x Chimera7 frame
- 1xTPU bottom stand incl. lock screw for GoPro
- 1x Caddx Ratel, 2.1mm lens camera
- 1x Albatross RHCP SMA 5.8GHz 150mm antenna
- 2 sets x Gemfan tri-blade 7040 props (Set of 4 - Color may vary)
- 4x 20*250mm Microfiber PU Leather Battery Strap (Color May Vary)
Additional Suggested Parts (not included)
- Adjustable mount (0-40) for GoPro
- 1300KV ?Cruiser, suggested battery: 6S 4000mAh
- 1800KV Speed Cruiser, suggested battery: 6S 2600mAh
No related record found