|
| Quantity | 0-3 | 4-50 | 51-100 |
| Discount | 0% OFF | 5% OFF | 10% OFF |
| Price | US$ 8.00 | US$ 7.60 | US$ 7.20 |
Copy and share this link on social network or send it to your friends
Copy| Product Name | BETAFPV BEC Board for Naked Camera for GoPro HERO6/7 Hero8 Action Camera 2-4S Input Voltage for FPV Racing Drone RC Quadcopter |
| Item NO. | F43365-D1 F43365-D2 |
| Weight | 0.022 kg = 0.0485 lb = 0.7760 oz |
| Category | DIY RC Drone Accessories |
| Brand | BETAFPV |
| Creation Time | 2021-03-30 |
You asked, we listen! To provide more choice for our customers, not only the BEC board for HERO6/7, BETAFPV also designed a new BEC board for GoPro HERO8. You don't need to worry your GoPro will turn off during a flight anymore. This BEC board only weighs about 1.5g, which makes your naked GoPro super neat and light. This BEC Board has integrated 5V@2A BEC, stock GoPro buttons, and LED pluggable connectors and remote recording!
Noticed: The BEC board for HERO8 does not fit the Case V2,
The two buttons on the BEC board have the same functions as the GoPro spare buttons. Three actions we will use frequently.
BEC Board for GoPro HERO6/7
Under normal operation, plug the GH1.25 connector into the GoPro Lite camera firstly, then connect with the battery. The LED will flash once, then you should press the Power/Mode button once in a second to power on. The LED on the BEC board has the same status as the stock LED on the GoPro mainboard.
|
Indication |
Button Operation |
LED Status |
|
Power On |
Press the Power/Mode button once |
Flash 3 times and light off |
|
Power Off |
Press the Power/Mode button for 5 seconds |
Flash 7 times and light off |
|
Start Record |
Press the record button once |
Continuously slow flash |
|
Stop Record |
Press the record button once |
Flash 3 times and light off |
|
Mode Switch |
Press the Power/Mode button once |
Check the mode on LCD Display |
The pilot could use the switch on the radio transmitter to start/stop the record. Some more configuration needed.
For example, if you use F4 FC V2.0 in the drone, like the 95X whoop drone, the connection diagram is shown below. The yellow cable (FC B12 pin pad) is just for the remote record.
We use the Pinio function in Betaflight to control the record. First, setup the Pinio function of the B12 pin in the FC board.
resource FLASH_CS 1 NONE
resource PINIO 1 B12
set pinio_box = 40,255,255,255
save
Next, map one of the switch channels in your radio transmitter to this Pinio (aka USER1). As shown below, we map the AUX4 channel in the radio transmitter to USER1 Pinio. The cursor in the orange zone means button released and the white zone means pressed. So keep the cursor in the orange zone in default.
Third, check if the Pinio function works. Change the switch and make the cursor move from the orange zone to the white zone, and finally back to the orange zone. Now you could check the LED status to know if the record starts. Use the same process to stop recording.
If you use the 12A F4 AIO FC board, like the 85X whoop drone, you will use the LED_STRIP pin (aka A08 pin pad) for the Pinio function.
resource LED_STRIP 1 NONE
resource PINIO 1 A08
set pinio_box = 40,255,255,255
save
Note: Do this at your own risk. You will lose your GoPro’s warranty and you may end up bricking the camera if something goes wrong. This guide is not authorized by GoPro and your camera is not guaranteed to work afterward. BETAFPV will not be held responsible for this action.
How to assemble the BEC Board on Naked Camera.
or
Email：yxy@xt-xinte.com
Wechat:15012645226
No related record found