Welding Combo for Mobula7 Upgrade Crazybee F4 Pro Flight Controller + Caddx 1200TVL FPV Camera & Switchable VTX + New Canopy V2

Welding Combo for Mobula7 Upgrade Crazybee F4 Pro Flight Controller + Caddx 1200TVL FPV Camera & Switchable VTX + New Canopy V2 Item NO: F27289-G/F27289-H/F27290-G/F27290-H/F27291-K/F27291-L

US$ 53.89 (10% Off)
US$ 59.88 Save US$ 5.99
Version:
DSMX FC FPV Camera DSMX FC FPV Camera VTX Frsky FC FPV Camera Frsky FC FPV Camera VTX FLYSKY FC FPV Camera FLYSKY FC FPV Camera VTX
Remark:
Customized Requirements
Quantity:
Shipping Cost:
Estimate Shipping Cost
Specifications
Product Name Welding Combo for Mobula7 Upgrade Crazybee F4 Pro Flight Controller + Caddx 1200TVL FPV Camera & Switchable VTX + New Canopy V2
Item NO F27289-G/F27289-H/F27290-G/F27290-H/F27291-K/F27291-L
Weight 0.1260 kg = 0.2778 lb = 4.4445 oz
Category DIY RC Drone Kit / RC Drone Accessories > DIY RC Drone Kit
Brand JMT
Creation time 2019-03-04

Detail

Welding Combo Kit for Mobula7 Upgrade Crazybee F4 Pro Flight Controller + Caddx 1200TVL FPV Camera & Switchable VTX + New Canopy V2

There are 2 kinds of Combo Kit optional, The electronic parts are well welded and tested. Please choose the version you request.

The Flight Controller compatible with DSM2/DSMX / Frsky / Flysky, Please choose the version according to your Remote Controller.


Warm Tips: Buyers can directly replace for using when you receive these item,It saves buyers' time. In addition, because the solder joints of these electronic parts are very fine, after welding and testing by our professional technicians, the after-sales problems are avoided to some extent. Please use them with confidence. These products do not require an additional welding fee. If the customer does not need to weld, please leave us a message , we will give you some relevant accessories as a gift.


Package include: (Upgrade combo)

1 x Crazybee F4 PRO flight controller (for Frsky or for DSM2/DSMX or for Flysky)

1 x 5V Buzzer Alarm Beeper

1 x Caddx.us Turbo EOS2 1200TVL 2.1mm 1/3 CMOS Mini FPV Camera
1 x 5.8g 40ch 25mw~200mw switchable VTX

1 x Camera Angle adjustable Canopy V2 Red

1 x Battery Holder Protection Seat Black TPU 3D Printing

1 x Relative Cables


Package include: (Basic combo)

1 x Crazybee F4 PRO flight controller (for Frsky or for DSM2/DSMX or for Flysky)

1 x 5V Buzzer Alarm Beeper

1 x Caddx.us Turbo EOS2 1200TVL 2.1mm 1/3 CMOS Mini FPV Camera
1 x 5.8g 40ch 25mw~200mw switchable VTX


 

Crazybee F4 Pro Flight Controller

(Frsky version) CRAZYBEE F4FR PRO V2.0 Firmware target: CrazybeeF4FR

(Flysky version) CRAZYBEE F4FS PRO V2.0 Firmware target: CrazybeeF4FS

(DSM2/DSM-X version) CRAZYBEE F4DX PRO V2.0 Firmware target: CrazybeeF4DX

(No RX version) CRAZYBEE F4 PRO V2.0 Firmware target: CrazybeeF4DX

MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)

Board size: 28.5 * 28.5MM
Power supply: 1-3S battery input (DC 3.5-13V)

Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready

Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable)

Flysky version Built-in SPI Flysky receiver with telemetry(AFHDS/AFHDS2A switchable)

DSM-2/X Version built-in Serial-based DSM-2/DSM-X compatible satellite receiver

No RX version need to add external Receiver

Built-in Betaflight OSD(SPI Control)

Built-in Current meter Max 28A

Current meter scale set to 1175

Built-in 5V 1A Buck / Boost with LC filter

Built-in voltage detection


 
Onboard 4 In 1 ESC

MCU upgraded to EFM8BB21

Power supply: 1-3S LiPo/LiPo HV (3.5v/13v)
Current: 5A continuous peak 6A (5 seconds)
Support BLHeliSuite programmable
Factory firmware: S_H_50_REV16_7.Hex
Default protocol: DSHOT600
 

Onboard Frsky NON-EU receiver Version
SPI BUS receiver
Frsky D8/D16 switchable
Compatible Non EU transmitter both D8 and D16 mode

Channels: 8ch or 16ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
 
Onboard Frsky EU-LBT Version
(External XM+ receiver)
 

Operating Voltage Range: 3.7~10V
Operating Current: 30mA @5V
Operating Range: Full range
With RSSI output on board: Analog 0~3.3V
Firmware Upgradeable, Default firmware EU-LBT with RSSI

Onboard Flysky receiver Version
SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
 

Onboard DSM-2 / DSM-X receiver version

Serial bus receiver
Protocol: DSM-2/DSM-X compatible
Channels:6-9 (Depend on your radio)
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
 
Canopy
Angle adjustable Canopy V2
CADDX Turtle V2 Camera
Image sensor: 1/2.7" CMOS sensor
Horizontal: 800TVL
TV system: NTSC/PAL changeable
Video Resolution: [email protected] / [email protected] / [email protected]
Power Input: DC 4.5-20V
FPV FOV: 155°
Recording FOV: 170°
Mini Illumination: 0.01lux
Image Resolution: 2 Megapixels
Lens: 1.8mm Turbo Eye Lens
Working Current: [email protected]/[email protected] (low consumption)
OSD Menu: Yes (Support Voltage Display)
Video Files: MP4
Audio: Support
Electronic Shutter : PAL : 1/50-100,000 NTSC : 1/60-100,100
S/N Ratio: >60dB (AGC OFF)
Video Output: CVBS
Max Micro SD Card Supported: 8-64GB(need Class 10 or above, recommend Class 10/UHS-I/UHS-II)
Color: Red 
VTX
Output power: 25~200mw switchable
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Antenna: RG178 antenna
Frequency: 5.8GHz 5bands 40 channels
With Raceband
Smartaudio ready
Weight: 3g
Battery Holder 

Black TPU 3D Printing


2019-05-13

Christian

Really nice combo.
It provided a great upgrade for my mobula7.
Flies really better

You May Also Like