Tracking
Category

Reviews (69)

Write a Review
Rating
Upload
HSP 1/10 540/550/3650 Carbon Brush Brushless Motor Cooling Radiator With Fan For RC Car
F20656
US$ 3.19
4.3
Reviews (69)
(37)
(13)
(19)
(0)
(0)
Image
United States
All
5
4
3
2
1
  • J****n
    Heat sink works well fan is junk fried out first install but put a better fan on it
    2020-10-03
  • St****ch
    Both arrived with only one mounting screw in the fan not even tight. Only 2 mounting holes line up with the fan. Very very cheaply made. As far as keeping the motor cool it works good. My motor was about 10-20 cooler. The only issue if your jumping/bashing it pops off. Running it on a castle 1/8 2200kv motor in a traxxas emaxx 3906
    2020-07-19
  • St****ch
    Both arrived with only one mounting screw in the fan not even tight. Only 2 mounting holes line up with the fan. Very very cheaply made. As far as keeping the motor cool it works good. My motor was about 10-20 cooler. The only issue if your jumping/bashing it pops off. Running it on a castle 1/8 2200kv motor in a traxxas emaxx 3906
    2020-07-19
  • Am****er
    I only got this because it matched my purple theme on my rc. The fan didn’t really seem to throw air so I just ended up taking it off but kept the heat sink on.
    2019-06-02
  • Am****er
    I only got this because it matched my purple theme on my rc. The fan didn’t really seem to throw air so I just ended up taking it off but kept the heat sink on.
    2019-06-02
  • J****n

    The only thing I don't like about this heatsink is it is very loose fitting on every motor I tried. If you buy this, you will need to shim it with aluminum foil, or epoxy it to the motor.
    2019-01-11
  • J****n
    The only thing I don't like about this heatsink is it is very loose fitting on every motor I tried. If you buy this, you will need to shim it with aluminum foil, or epoxy it to the motor.
    2019-01-11
  • J****n

    The only thing I don't like about this heatsink is it is very loose fitting on every motor I tried. If you buy this, you will need to shim it with aluminum foil, or epoxy it to the motor.
    2019-01-11
  • J****n
    The only thing I don't like about this heatsink is it is very loose fitting on every motor I tried. If you buy this, you will need to shim it with aluminum foil, or epoxy it to the motor.
    2019-01-11
  • J****n

    The only thing I don't like about this heatsink is it is very loose fitting on every motor I tried. If you buy this, you will need to shim it with aluminum foil, or epoxy it to the motor.
    2019-01-11
  • Xo****ox

    It works well keeping motor cool, I own a 2wd slash. The motor is a castle creations 5700kv and gets quite hot when punching the throttle. I can run 2 packs back to back no problem fitment is an issue and took some finegaling to get it to seat right. There about 1/4 of the motor that isn't covered due to transmission case. With a metal hop-up transfer case it would fit no problem.
    2018-11-24
  • Xo****ox
    It works well keeping motor cool, I own a 2wd slash. The motor is a castle creations 5700kv and gets quite hot when punching the throttle. I can run 2 packs back to back no problem fitment is an issue and took some finegaling to get it to seat right. There about 1/4 of the motor that isn't covered due to transmission case. With a metal hop-up transfer case it would fit no problem.
    2018-11-24
  • Xo****ox

    It works well keeping motor cool, I own a 2wd slash. The motor is a castle creations 5700kv and gets quite hot when punching the throttle. I can run 2 packs back to back no problem fitment is an issue and took some finegaling to get it to seat right. There about 1/4 of the motor that isn't covered due to transmission case. With a metal hop-up transfer case it would fit no problem.
    2018-11-24
  • Xo****ox
    It works well keeping motor cool, I own a 2wd slash. The motor is a castle creations 5700kv and gets quite hot when punching the throttle. I can run 2 packs back to back no problem fitment is an issue and took some finegaling to get it to seat right. There about 1/4 of the motor that isn't covered due to transmission case. With a metal hop-up transfer case it would fit no problem.
    2018-11-24
  • Xo****ox

    It works well keeping motor cool, I own a 2wd slash. The motor is a castle creations 5700kv and gets quite hot when punching the throttle. I can run 2 packs back to back no problem fitment is an issue and took some finegaling to get it to seat right. There about 1/4 of the motor that isn't covered due to transmission case. With a metal hop-up transfer case it would fit no problem.
    2018-11-24
  • Am****er

    Fast shipping. Fan is decent not to loud. The reason why 3 stars is its missing 2 screws but if u look carefully at the pictures it only show 2 screws
    2018-02-20
  • Am****er

    Fast shipping. Fan is decent not to loud. The reason why 3 stars is its missing 2 screws but if u look carefully at the pictures it only show 2 screws
    2018-02-20
  • Am****er
    Fast shipping. Fan is decent not to loud. The reason why 3 stars is its missing 2 screws but if u look carefully at the pictures it only show 2 screws
    2018-02-20
  • Am****er

    Fast shipping. Fan is decent not to loud. The reason why 3 stars is its missing 2 screws but if u look carefully at the pictures it only show 2 screws
    2018-02-20
FAQ Center
How Can I know all Xt-xinte's Activities
How to earn credits to get money
Get More credits during 2019
Shipping Service
Free Lottery
Company Info
Feedback
Customer Reviews
About Us
Contact Us
News
Authorization Certifications
Forget Password
My Orders
Tracking Order
My Account
Register
Copyright © 2006-2050 SHOP INC. All Rights Reserved.