Product Name | BETAFPV F4 1S AIO Brushless Flight Controller with SPI Frsky D16 FCC / D16 LBT/ Futaba S-FHSS PNP for RC FPV Tinywhoop Drone |
Item NO. | F45585 F45586-D1 F45586-D2 F45586-D3 |
Weight | 0.02 kg = 0.0441 lb = 0.7055 oz |
Category | DIY RC Drone Accessories > Flight Control |
Brand | BETAFPV |
Creation Time | 2021-12-11 |
Integrated with a 25mW VTX, this AIO board(Frsky/Futaba Rx) is ultralight only 3.92g, which can extremely save the weight of building a drone, perfectly suitable for the 1S weight-sensitive drone such as Meteor65 HD and HX100 SE.
F4 1S AIO FC(No Rx) not only integrates with the 25mW VTX but also supports a 1-2S power system, which is perfectly suitable for weight-sensitive drones such as Meteor75 and Beta85 Pro2.
This AIO board also reserves a Plug & Play port for the C01 Camera,C01 Pro Camera, and BETAFPV Nano HD Camera, no soldering work needed, super convenient for installation.
Specially added with 2 RGB LED indicators, this board brings the drone an incredible light effect while pilots flying on the night.
This board can handle 5A continuous current(6A burst), supports the 1S lipo battery, brings the drone a stronger flight performance.
Come with a BT2.0 connector, it solves the problem of voltage sag, the discharge can be more efficient, which brings this board a better performance on function for power and responsiveness.
Item: F4 1S AIO FC(Frsky/Futaba Rx)
Weight: 3.92g(without antenna and BT2.0 connector)
VTX Power: 25mW
CPU: STM32F411CEU6 (100MHZ )
Six-Axis: MPU6000 (SPI connection)
Firmware version: betaflight_4.2.0_STM32F411
Receiver: Support Frsky Receiver/ Futaba Receiver
Motor Pin Connecter: 1.25mm Header Pins
Mounting hole size: 29mm x 29mm / suitable for almost all kinds of whoop frame
Specification of ESC
Built-in ESC with 5A continuous and peak 6A current
Input voltage: 1S Lipo
ESC firmware: O_H_5_REV16_8.HEX
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Signal support: D-shot150, D- shot300, D-shot600, Oneshot125, Multishot, PWM
4 Indicators: Receiver indicator (Blue)/Flight control status indicator (Green)/Flight control power indicator (Red)/VTX indicator (Pink)
Diagram for F4 1S AIO FC(SPI Rx)
SPI Receiver CC2500
Come with the build-in SPI Receiver CC2500, F4 1S AIO FC(SPI Rx) can compatible with Futaba S-FHSS, Frsky D8, and D16 protocol. The default Frksy protocol is Frsky D16, if pilots buy the wrong receiver of the SPI Frsky version or upgrade the wrong firmware accidentally, which need to switch the protocol to Futaba or FrskyD8, please upgrade the Betaflight Firmware according to this tutorial.
Configuration |
Protocol |
FRSKY_D |
Frsky D8 |
FRSKY_X |
Frsky D16 FCC |
FRSKY_X_LBT |
Frsky D16 LBT |
SFHSS |
Futaba S-FHSS |
There are 4 LEDs on the bottom of the board to indicate the status, including the Receiver LED ( Blue), FC Status LED(Green), FC Power LED ( Red ), and VTX LED(Pink).
LED |
Status |
Description |
Receiver LED ( Blue) |
Solid |
Connected or in bind mode |
Receiver LED ( Blue ) |
Flashing |
Not connected |
Power LED ( Red ) |
Solid |
Power on |
Status LED ( Green ) |
Solid |
Motor Armed |
Status LED ( Green ) |
Flashing |
Motor Disarmed |
Status LED ( Green ) |
Off |
Bind |
VTX LED ( Pink ) |
Flash Slowly |
Work |
Battery: BT2.0 300mAh 1S Battery / BT2.0 450mAh 1S Battery / BT2.0 260mAh 1S Battery
Frame: Meteor65 Frame / Meteor75 Frame
Props: 31mm 4-Blades props / 40mm 4-blades props
Motors: 0603 motors / 0703 motors / 0802 motors / 0802SE 22000KV Motor
Camera: C01 Camera / C01 Pro Camera / BETAFPV Nano HD Camera
Item: F4 1S AIO FC(No Rx)
Weight: 3.83g (without antenna and BT2.0 connector)
VTX Power: 25mW
CPU: STM32F411CEU6 (100MHZ )
Six-Axis: MPU6000 (SPI connection)
Firmware version: betaflight_4.2.0_STM32F411
Receiver: Support External Receiver, SPI Receiver, including Frsky XM/XM+ receiver, Futaba receiver, Crossfire receiver, and DSMX receiver
Motor Pin Connecter: 1.25mm Header Pins
Mounting hole size: 29mm x 29mm / suitable for almost all kinds of whoop frame
Specification of ESC
Built-in ESC with 5A continuous and peak 6A current
Input voltage: 1-2S Lipo
ESC firmware: S_H_70_REV16_7.HEX
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Signal support: D-shot150, D- shot300, D-shot600, Oneshot125, Multishot, PWM
4 Indicators: Receiver indicator (Green)/Flight control status indicator (Blue)/Flight control power indicator (Red)/VTX indicator (Pink)
Diagram for F4 1S AIO FC(No Rx)
For more convenience to the pilots, we specially design the Plug & Play SPI Frsky Rx for the F4 1S AIO FC(No Rx), no soldering work needed, super easy to install.
There are 4 LEDs on the bottom of the board to indicate the status, including the Receiver LED (Green), FC Status LED(Blue), FC Power LED ( Red ) and VTX LED(Pink).
LED |
Status |
Description |
Receiver LED ( Green) |
Solid |
Connected or in bind mode |
Receiver LED ( Green) |
Flashing |
Not connected |
Power LED ( Red ) |
Solid |
Power on |
Status LED ( Blue ) |
Solid |
Motor Armed |
Status LED ( Blue ) |
Flashing |
Motor Disarmed |
Status LED ( Blue ) |
Off |
Bind |
VTX LED ( Pink ) |
Flash Slowly |
Work |
Battery: BT2.0 300mAh 1S Battery / BT2.0 450mAh 1S Battery / BT2.0 260mAh 1S Battery/ BT2.0 300mah 2S Battery
Frame: Meteor65 Frame / Meteor75 Frame / Beta85 Pro2 Frame
Props: 31mm 4-Blades props / 40mm 4-blades props / Gemfan 2020 4-Blades Props
Motors: 0603 motors / 0703 motors / 0802 motors / 0802SE 22000KV Motor / 1103 11000KV motors / 1102 18000KV motor
Camera: C01 Camera / C01 Pro Camera / BETAFPV Nano HD Camera
1 * F4 1S AIO Brushless Flight Controller
4 * M1.2x4mm Screws
4 * M1.4x5mm Screws
4 * Anti-vibration Rubber dampers
SKYPE: +8615012643826
Email:yxy@xt-xinte.com
No related record found