iFlight SucceX-A F4 40A AIO Board Flight Controller FC Integrated 40A ESC MPU6000 2-6S For RC DIY FPV Racing Drone DJI Air Unit Item NO.: F38179

iFlight SucceX-A F4 40A AIO Board Flight Controller FC Integrated 40A ESC MPU6000 2-6S For RC DIY FPV Racing Drone DJI Air Unit

PRODUCT DESCRIPTION
The SucceX-A F4 AIO(F4+40A) NEXT-GEN flight controller you need for your build. This FC is ready for anything with 5 uarts,4 motor outputs, 8Mb blackbox and a powerful F4 processor to run it all. Designed to work seamlessly with DJI’s new HD FPV system. To make things even simpler, the DJI Air unit can just be plugged into the AIO FC with the included wire harness. In addition, we added the popular and reliable USB Type-C instead of Micro USB and therefore the same standard than your DJI module.

Attention: This AIO-Board was specifically designed to run with a DJI Air Unit and takes advantage of DJI‘s latest Betaflight OSD pass-through! Because of space limitations we needed to take compromises and removed analog OSD support for this board! If you need analog OSD functionality, please check our latest releases.

Top Features:
• DJI Plug-and-Play - No need to solder tiny wires!
• Gyro Fusion - Zero delay Twin-Gyro filtering!
• Dual BEC 5V and 10V
FC // SucceX-A F4 AIO
MCU: 168MHz STM32F405
Gyro：MPU6000
Blackbox：8MB
OSD Chip: NO (Analog OSD not available)
OSD Betaflight: YES (Digital DJI Air Unit pass-through)
BEC: 5V 2.5A  (3A MAX) / 10V 2.5A (3A MAX)
Voltage sensor scale: 110
Current sensor scale: 100
Inverter for SBUS input (UART2-RX)
Beeper pad : Yes
RSSI input pad: No
UARTs：5
Motor outputs: 4
8 pin for DJI air unit port (10V，GND，T1，R1，GND，R2I，T2，5V)
BLHeli32 Telemetry：RX4
Input voltage：recommended 2-6S
Firmware: IFLIGHT_F405_AIO
Mounting pattern: 30.5*30.5mm φ4mm with Grommets φ3mm
Dimensions:   40.5*43mm
Weight: 11.4g
USB type-C
ESC // SucceX 40A 2-6S

Top Features:
- 6 layers double-sided PCB board
- 2oz 1.6mm thick power board
- 32bit STM32F051 MCU, 48M maximum clock speed
- TDK MLCC Low ESR ceramic capacitors
- Top grade TPN2R304PL MOSFET

Specification:
MCU: STM32F051
Up tp 48M PWM frequency
Capacitance: 484uF
Current Sensor: Yes
Input: 2-6S LIPO
Constant: 40A / Burst: 50A
BlHeli32 telemetry: Yes
BEC: 5V/500MA
Supports up to Dshot1200, Proshot, Oneshot, Multishot 
Target: iFlight-BL32-4IN1
Mounting pattern: 30.5*30.5mm/Φ4mm
Dimensions: 43*39mm (including the power pads)

Package Includes：
- SucceX-A F4 AIO × 1
- Capacitor 470uF/50V × 1
- XT60 12AWG cable
- Wire harness (plug&play) for DJI Air Unit × 1
- M4 to M3 silicon grommets × 4