Chimera7 Pro HD BNF Included Components and Parts
4 x HQ 7.5X3.7X3 CW propeller + 4 x HQ 7.5X3.7X3 CCW (Color may vary)
2 x Albatross LHCP 5.8GHz SMA FPV Antenna
2 x iFlight Lipo Strap 20*250mm (Black)
1 x Pre-built and Tested Chimera7 Pro
1 x DJI FPV Air Unit Module + Camera
Introducing what has been requested for too long already! A super-efficient iFlight
7inch Long-Range bird that can go where you couldn't go before and can
carry bigger batteries to get the flight time to surf the swiss alps if
you want! A super stiff frame for minimum resonance and XING2 2809
motors for maximum 7inch prop control. Fly big batteries top-mounted, or
even bigger batteries bottom-mounted, 6cells recommended or 5cells for
slow cruising. But whatever style you fly, a Lipo or Lion pack will just
do the job. Recommended 5S 3.000mAh above (slow cruising) or 6S
2.500mAh above.
GPS
functionality to find your way back and Betaflight GPS Rescue mode ready
to setup (default OFF to prevent unexpected behavior; Setup
instructions included). Vertical and horizontal TBS Crossfire antenna
mounts are included to cover you and your antenna dead-ends just in
case. GoPro universal TPU bottom stand included; fits your original
GoPro bracket and our TPU GoPro protectors (additional).
Main Changelog from Chimera7 to Chimera7 Pro:
SucceX-D F7 V2.2 Stack (F7+50A ESC) upgraded to BLITZ F722 Stack (F7 V1.1 + 55A 4in1 ESC)
New Lightweight Side Panels Design - Keep Your Rig Clean
XING 2806.5 upgraded to XING2 2809 1250KV
7-inch frame upgraded to 7.5inch
HIGHLIGHTS:
Battery voltage LED status light (illuminated IF logo on the bottom)
360° TPU protection, DJI cam protection and antenna mounts
GoPro TPU bottom stand (GoPro protector not included)
Lightweight Side Panels Design - Keep Your Rig Clean
No props in view (DJI Air unit record in 1080p/60fps)
XING2 2809 1250KV efficient wide stator motors
GPS pre-installed for more safety at a distance
6mm rigid arm design for more stiffness
Top- and bottom battery mount option
PRE-TUNED & PRE-SETUP:
Is this your first BNF or are you just starting through with FPV? This article might probably help: General Guide // iFlight BNF
Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!
To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"
Angle-Mode (self-balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!
Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode"
GPS Rescue is OFF by default to prevent unwanted or unexpected drone behavior.
Please check our linked article on "GPS Rescue Mode // Setup"
Specifications:
Weight: 695g (without battery and GoPro mount)
Total Dimensions: 258*200mm (body dimension)
Bottom to Top Distance: 20-29mm
Arm Thickness: 6mm
Upper(middle) Plate Thickness: 3mm
Bottom Plate Thickness: 3mm
Camera Plate Thickness: 3mm
Top Plate Thickness: 2mm
Geometry: DC (DeadCat)
HQ 7.5X3.7X3 Propellers
XING2 2809 1250KV
FC // BLITZ F722
ESC // BLITZ E55 4-IN-1 2-6S ESC
ELECTRONICS // BLITZ F7 Stack (F7 V1.1 + 55A 4in1 ESC)：
BLITZ F722 Flight Controller
Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter
Smartaudio / IRC Tramp VTX protocol supported
Firmware target: IFLIGHT_BLITZ_F722
Motor outputs: 4x (SH1.0 connector)
Flash: 32MB (Blackbox flash)
I2C serial: SDA / SLA pads
Dimensions: 36.5*35 mm
Barometer: DPS310
OSD Chip: AT7456E
LED controller: Yes
MCU: STM32 F722
Beeper pad: Yes
Gyro: BMI270
Weight: 7.8g
UARTS: 6
ESC // BLITZ E55 4-IN-1 2-6S 55A ESC
Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.
Mounting Holes: 30.5*30.5mm/Φ4mm
Target: IFLIGHT_BLITZ_G2
Supports 2-6S Lipo input
Current sensor: Yes
Constant: 55 Amps
Current rate: 200
Burst: 65 Amps
Weight: 15.3g
MCU： G071
BEC: No
Note:
All iFlight BNFs are tested before shipment to guarantee the highest quality.
If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.
iFlight takes no responsibility for issues with DJI or Caddx 3rd party gear
(Video transmitters, Goggles, Radios, etc) and must be directly reported
to www.caddxfpv.com/pages/contact-us or www.dji.com/support.
No related record found