Mini F3 OSD fly Tower Integrated Flight Control 20mmx20mm 10A 4in1 ESC For FPV Racing Drone RC Racer Item NO.: F22894

20mmx20mm mounting hole spacing, ultra-small size, fully functional, integrated Betaflight OSD, with 4in1 10A DSHOT600 protocol ESC

HALO F3 OSD flight control
First, Omnibus F3 miniature version of the flight control integrated MPU6000 accelerometer gyroscope, integrated OSD
1. Specially designed for small cross machine, suitable for the following size rack within 250mm, especially the 90-130mm rack can play more advantages of small and full function;
2. This board provides all the features of Omnibus F3 flight control, weighs only 2.2g, size is only 27 * 27MM, fixed hole for 20MM (M2.5 hole);
3. Designed for 4-axis models tailored to support Betaflight firmware (Omnibus F3 firmware), the default shipping has been updated to 3.2.1 version
4. Use STM32F3CCT6 256K flash MCU, MPU6000 SPI interface sensor connection, faster computing speed;
5. Support 2-3S power input;
6. Built-in 5V BEC for 25mw map transmission machine use
7.Supports mainstream receivers such as SBUS / PPM / IBUS / DSMX;
8. Buzzer / LED programming / voltage monitoring / BLHELI ESC;

BS410 four-in-one ESC
Second, 4 IN 1 through the machine BLHELI_S ESC
Technical Parameters:
1. Input voltage: 2-3S LiPo / 2-3S HV LiPo
2.BEC output: None
3. A single ESC continuous operating current: 10A (maximum current: 15A 5 seconds)
4. Four-in-one ESC Size: 27 * 31mm (including the largest pad and protruding size)
5. Four in one ESC weight: 3.7g
6. Firmware: BLHELI_S
7. Support DSHOT, Oneshot, positive and negative
8. Processor: SILABS EFM8BB21F16G
9.MOS tube: TPN2R703NL
10. Drive: a new generation of three-in-one MOS driver

Third, Mini F3 flying tower basic parameters:
1. One tower weight: 9g
2. Support rack range: 250mm rack are applicable
3. Continuous working current: 10A * 4 (maximum current: 15A * 4 5 seconds)
4 fly tower has good welding LC filter, can effectively improve the video ripple.

All receiver signal lines should be connected to RC_IN interface and select the corresponding voltage output interface according to receiver parameters. If SBUS IBUS or DSM2 / DSMX receiver, please open UART3 RX as serial receiver and select corresponding receiver Machine agreement.

Specification:
HALO F3 +OSD Flight controller
-Size:27mm*27mm*5mm
-Mount hole: 20mm*20mm
-Processor: STM32 F303 MCU
-Sensor: SPI Sensor MPU6000
-Built-in Betaflight OSD ( Batt voltage, RSSI , Artificial Horizon , Fly mode , -Flytime, Craft name etz.)
-Firmware version: Betaflight 3.2.0 Dshot ready
-Target: OmnibusF3
-Power support : 5v~12v(2S-3S Lipo)

BS410 10A 4in1 ESC
-Size:27mm*27mm*5mm
-Mount hole: 20mm*20mm
-Firmware version: BLHELI_S 16.5
-Firmware target: F-H-40
- BB2, 48MHZ Chip
-Lipo Battery: 2S-3S
-Con. Current: 10A
-Peak Current: 15A (10S)
-BEC: 5V @0.1A
-Programming: YES
-Betaflight pass-trough ready
-Dshot600 ready(Default)

Package include:
-Flight controller *1
-LC power filter *1
-M2*5+6 nylon hex column *8
-M2*5 nylon screw *4
-M2 nylon nut *4
-Cables