Home>DIY RC Drone Accessories>Holybro PM03D Power Module XT30 XT60 6S Compatible to Flight Controller Uses I2C Power Monitor for X500 Multirotor
Holybro PM03D Power Module XT30 XT60 6S Compatible to Flight Controller Uses I2C Power Monitor for X500 Multirotor

Holybro PM03D Power Module XT30 XT60 6S Compatible to Flight Controller Uses I2C Power Monitor for X500 Multirotor Item NO.: F48717

Write a Review
US$ 41.17
US$ 48.44 Save US$ 7.27 (15% Off)
Quantity

Copy and share this link on social network or send it to your friends

Copy
  • Holybro PM03D Power Module XT30 XT60 6S Compatible to Flight Controller Uses I2C Power Monitor for X500 Multirotor
Product Name Holybro PM03D Power Module XT30 XT60 6S Compatible to Flight Controller Uses I2C Power Monitor for X500 Multirotor
Item NO. F48717
Weight 0.095 kg = 0.2094 lb = 3.3510 oz
Category DIY RC Drone Accessories
Brand Holybro
Creation Time 2022-10-27

Holybro PM03D Power Module XT30 XT60 6S Compatible to Flight Controller Uses I2C Power Monitor for X500 Multirotor

Product Details:
Overview
This PM03D Power Module supplies clean 5.2V to flight controller from the battery and provides current consumption
and battery voltage measurements via I2C digital signal through a 6 Pin 2mm Pitch CLIK-Mate cable, along with
integrated esc power for up to 10 ESCs. Compatible to flight controller that uses I2C power monitor such as the
Pixhawk 5X and 6X.

It is design for multi-rotor like the X500 V2. It has both XT-30 & XT-60 connectors preinstalled for motor ESCs and
Battery, as well as two 5V BEC and a selectable 8V/12V output different kinds of peripheral devices.

Note: This PM is not compatible with flight controller that uses analog PM such as the Pixhawk6C, Pixhawk4,
Pixhawk4 Mini, pix32 v5, or Durandal flight controllers.

Features
1.Plug & play, no additional setup required for QGroundcontrol & Mission Planner
2.XT-30 connectors and solder pads for easy motor ESC connection
3.Onboard voltage regulators: two 5.2V & one selectable 8V/12V
4.5V/A ports for powering companion computer or peripheral device
5.Selectable 8V or 12V triple row pin header for powering peripheral device

Technical Specification:
Maximum input voltage: 6S battery
PCB Cont. Current Rating: 90A
PCB Burst Current Rating: 140A (<60 Sec)
Max current sensing: 164A
Connections
XT-60 for battery
XT-30 for motor & peripheral device (battery voltage)
Solder pads in each corner (battery voltage)
CLIK-Mate 2.0mm for flight controller (5.2V/3A standalone BEC)
JST GH 4pin (5.2V/3A, BEC shared with 5.2V triple row pin header)
2x Triple row pin header (5.2V/3A, BEC shared with JST GH 4pin)
2x Triple row pin header (8V or 12V selectable by moving header jumper, 3A)
Dimension: 84*78*12mm (excluding wires)
Mounting: 45*45mm
Weight: 59g

Please Note:
The XT60 plug and 12AWG wire that PM03D comes with is rated for 30A continuous current and 60A instantaneous current
(<1 minute). If a higher current is being used, the plug type and wire size should be changed accordingly. You can
refer to this chart as reference.

Package Includes
1x PM06 board
1x 80mm XT60 connector wire (pre-soldered)
1x Electrolytic capacitor: 220uF 63V (pre-soldered)
1x 2.0mm pitch CLIK-Mate 6pin cable (To power flight controller)
4pin JST GH to USB Type C
4pin JST GH to barrel plug (2.1*5.5mm)
4pin JST GH to barrel plug (2.5*5.5mm)
4pin Pin Dupont Cable (2pc)
Nylon standoffs & nuts


No related record found