Holybro Kakute F7 AIO STM32F745 Flight Controller w/ OSD PDB Current Sensor Barometer for RC Drone

Copy and share this link on social network or send it to your friends

Copy

Holybro Kakute F7 AIO STM32F745 Flight Controller w/ OSD PDB Current Sensor Barometer for RC Drone Item NO: F31844

US$ 40.90
Quantity:
Shipping Cost:
Free Shipping
  • Holybro Kakute F7 AIO STM32F745 Flight Controller w/ OSD PDB Current Sensor Barometer for RC Drone
Product Name Holybro Kakute F7 AIO STM32F745 Flight Controller w/ OSD PDB Current Sensor Barometer for RC Drone
Item NO F31844
Weight 0.0500 kg = 0.1102 lb = 1.7637 oz
Category DIY RC Drone Kit / RC Drone Accessories > Flight Control
Brand Holybro
Creation time 2019-09-12

Holybro Kakute F7 AIO STM32F745 Flight Controller w/ OSD PDB Current Sensor Barometer for RC Drone


Overview:
Specification(manual):
Brand name: Holybro
Item name: kakute F7
Features:
  all using your transmitter sticks and goggles.
  to soft-mount the board itself.
  from the battery power lead.
  peripherals such as receiver, video transmitter, FPV camera, or LED strip.

Package included:
1x kakute F7 flight controller
The Holybro Kakute F7 All-In-One flight controller makes it easy to build your multirotor. It integrates
flight controller (FC), power distribution board (PDB), and on-screen display (OSD) in one. The Kakute F7
AIO’s layout makes it easy to wire up the other components of the multirotor while keeping the build
neat and tidy.
MCU: STM32F745 32-bit processor
IMU: ICM20689 (SPI)
Barometer: BMP280
Current Sensor: Approximately 130 amps maximum measurable value
USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
6 hardware UARTS (UART1,2,3,4,6,7)
All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
TF card for Blackbox logging
Dimensions: 35x48x7mm (includes foam-mounted gyro board in height)
Mounting Holes: Standard 30.5mm square to center of holes
Weight: 11g
• Supports Betaflight, Butterflight, and Cleanflight.
• Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level,
• Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need
• High-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz sampling rate.
• Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA pads for use with external GPS/magnetometer units.
• 2 oz. copper PCB allows up to 120A maximum continuous current.
• Dedicated bootloader button for easy firmware flashing.
• Low-profile design fits into even very compact frames.
• Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).
• Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F7 AIO monitors voltage directly
• Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 2 amps and 3.3v at up to 200 mA to power
• Supports BLHeli pass-through for easy ESC upgrade and configuration.



No related record found