Home>DIY RC Drone Accessories>Mobula7 Upgrade Parts>Happymodel Crazybee F4 Pro V2.0 1-3S Compatible Flight Controller for Mobula7 Mobula 7 HD Internal Frsky/Flysky/DSM2/DSMX Protocol RX
Happymodel Crazybee F4 Pro V2.0 1-3S Compatible Flight Controller for Mobula7 Mobula 7 HD Internal Frsky/Flysky/DSM2/DSMX Protocol RX

Happymodel Crazybee F4 Pro V2.0 1-3S Compatible Flight Controller for Mobula7 Mobula 7 HD Internal Frsky/Flysky/DSM2/DSMX Protocol RX Item NO.: F28042-F28043-F28044-F28045

4.0
(2)
Write a Review
US$ 41.64
US$ 48.99 Save US$ 7.35 (15% Off)
Sold Out

Copy and share this link on social network or send it to your friends

Copy
  • Happymodel Crazybee F4 Pro V2.0 1-3S Compatible Flight Controller for Mobula7 Mobula 7 HD Internal Frsky/Flysky/DSM2/DSMX Protocol RX
  • Notes:
  • The biggest differences between Crazybee F4 PRO V1.0 and V2.0 are:
  • V2.0 could handle 1-3s Lipo/LiHV
  • V1.0 could handle only 1-2s Lipo/LiHV
  • V2.0 use bigger bind and boot button , change the BAT/GND pad to “through hole”
Product Name Happymodel Crazybee F4 Pro V2.0 1-3S Compatible Flight Controller for Mobula7 Mobula 7 HD Internal Frsky/Flysky/DSM2/DSMX Protocol RX
Item NO. F28042-F28043-F28044-F28045
Weight 0.02 kg = 0.0441 lb = 0.7055 oz
Category DIY RC Drone Accessories > Mobula7 Upgrade Parts
Brand Happymodel
Creation Time 2019-03-25

Happymodel Crazybee F4 Pro V2.0 1-3S Compatible Flight Controller for Mobula7 Mobula 7 HD Internal Frsky/Flysky/DSM2/DSMX Protocol RX

Notes: 

The biggest differences between Crazybee F4 PRO V1.0 and V2.0 are:

V2.0 could handle 1-3s Lipo/LiHV

V1.0 could handle only 1-2s Lipo/LiHV

V2.0 use bigger bind and boot button , change the BAT/GND pad to “through hole”

Flight controller MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 1-3S battery input (DC 3.5-13V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
ESC MCU Upgraded to EFM8BB21
Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable)
Flysky version Built-in SPI Flysky receiver with telemetry(AFHDS/AFHDS-2A Compatible)
DSMX version Built-in Serial-based DSM2/DSMX compatible satellite receiver(Default RX2 was used for DSM2/DSMX receiver)
No RX version support external serial-bus receiver like xm+, crossfire, S-FHSS and Dsm2/DSMX, Ibus protocol etc.
Built-in Betaflight OSD (SPI Control)
Built-in Current meter sensor Max up to 28A
Current meter scale set to 1175
Built-in 5V 1A Buck / Boost with LC filter
Built-in voltage detection
BLHELI_S pass-through Ready
Multi Serial port support
Fully compatible with almost Brushless whoop drone
Weight:4.3g
Onboard 4in1 ESC MCU upgraded to EFM8BB21
Power supply: 1-3S LiPo/LiPo HV (3.5v/13v)
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: S_H_50_REV16_7.Hex
Default protocol: DSHOT600
Receiver support No RX version support external serial-bus receiver like xm+, crossfire, S-FHSS and Dsm2/DSMX, Ibus protocol etc.

Firmware target:

Frsky version  betaflight_4.0.0_CRAZYBEEF4FR.hex

Flysky version betaflight_4.0.0_CRAZYBEEF4FS.hex

DSM2/DSMX version betaflight_4.0.0_CRAZYBEEF4DX.hex

No RX version betaflight_4.0.0_CRAZYBEEF4DX.hex



Crazybee F4FR PRO frsky version firmware target CrazybeeF4FR

betaflight_4.0.0_CRAZYBEEF4FR_20181211

Crazybee F4FS PRO flysky version firmware target CrazybeeF4FS

betaflight_4.0.0_CRAZYBEEF4FS_20181218

Crazybee F4DX PRO DSM2/X version and Crazybee F4 PRO No RX version firmware target CrazybeeF4DX

betaflight_4.0.0_CRAZYBEEF4DX_20181211

Betaflight Official will update firmware target from V3.5.5


Package include:
1 x CrazybeeF4 PRO flight controller
3 x Power cables
1 set Shock absorbing rubber and screws


2019-05-25

J****s

This seems like a really promising board, but it didn't work out for me - it failed after about 8 flights. It's possible I over stressed it with over sized motors, although the failure came after arming and before take off, and the previous flight had been some very gentle flying with carefully monitored current. Such is life.

On the plus side: I really liked the current monitoring, this is the first board that I had that provided it. The Flysky eceiver worked well with good range, although I couldn't get rssi to display on the osd. It doesn't seem to be connected to the analog input, and it doesn't appear on an aux channel like the Fli14 receivers. The OSD was clear and stable.

Personally, I don't think I will be buying any more Crazybees given the price and the question mark over reliability/QC.

2019-05-10

C****.

Really good development. It can handle even 3S on awhoop.
Thats awesome