Home>DIY RC Drone Accessories>CUAV New Pixhack V5 Nano Small Flight Controller with NEO V2 GPS Integrated Buzzer For Ardupilot PX4 Drone Fixed-wing Aircraft Helicopter Parts
CUAV New Pixhack V5 Nano Small Flight Controller with NEO V2 GPS Integrated Buzzer For Ardupilot PX4 Drone Fixed-wing Aircraft Helicopter Parts

CUAV New Pixhack V5 Nano Small Flight Controller with NEO V2 GPS Integrated Buzzer For Ardupilot PX4 Drone Fixed-wing Aircraft Helicopter Parts Item NO.: F32289 F32290 F32289-A

Write a Review
US$ 58.86
US$ 69.25 Save US$ 10.39 (15% Off)
Sold Out

Copy and share this link on social network or send it to your friends

Copy
Product Name CUAV New Pixhack V5 Nano Small Flight Controller with NEO V2 GPS Integrated Buzzer For Ardupilot PX4 Drone Fixed-wing Aircraft Helicopter Parts
Item NO. F32289 F32290 F32289-A
Weight 0.105 kg = 0.2315 lb = 3.7038 oz
Category DIY RC Drone Accessories
Brand CUAV
Creation Time 2019-10-09

CUAV New Pixhack V5 Nano Small Flight Controller with NEO V2 GPS Integrated Buzzer For Ardupilot PX4 Drone Parts

V5 nano is an autopilot for space-constraint applications designed by CUAV in collaboration with the PX4 team. It is based on the Pixhawk FMUv5 design standard and is optimized to run PX4 firmware, and is also compatible with ArduPilot firmware.

2

2.6mm间距性能强大

传感器双平台兼容全机型支持

参数对比en规格参数en

Features:
- Compact but powerful V5 nano flight controller + NEO GPS 
- Support for hardware on open source platform PX4 and Autopilot 
- Suitable for fixed-wing drones, helicopters, multicopters, FPVs, VTOL, Unmanned Boats, UAVs
- High Performance: Equipped with STM32F765 microprocessor, features 216MHz main frequency, 2M flash and 512K SDRAM. There are four groups of isolation chips and a MS5611 high-precision air gauge. 
- Easy to install and dismantle with 2.6mm spacing between IO pins. 
- Real-time Data Monitor: Five groups of built-in sensors enhance its safety and stable performance. There are ICM-20689 accelerometer and gyroscope, ICM-20602 accelerometer and gyroscope, BMI055 accelerometer and gyroscope, IST8310 magnetic compass and MS5611 air gauge.

Specifications:
Hardware Parameters: 
- Main FMU Processor: STM32F765(32-bit, 216MHz, 2MB flash, 512KB RAM)

Sensors: 
- Accelerometer: ICM-20602/ICM-20689/BMI055
- Gyroscope: ICM-20602/ICM-20689/BMI055
- Magnetometer: IST8310
- Air Gauge: MS5611

Interfaces:
- UART Ports: 5
- I2C Ports: 4
- PWM Output: Up to 11
- PWM Input: 4
- Signal Input Protocol for Remote Control: PPM/SBUS/DSM
- RC IN: 1
- PPM IN:1
- RSSI Input: PWM or 3.3V analog voltage 
- CAN Standard Bus: 2
- Current & Voltage Input: 1
- Safety Switch: 1
- GPS Port: 1
- Debug Port: 1
- JATG Port: 1
- USB Port: 1 (Type-C)

Supported Models:
- For PX4 Hardware: Fixed-wing Aircrafts, 3-8 Multicopters, Helicopters, VTOL, UAVs, Unmanned Boats 

Working Conditions & Physical Parameters:
- PM Working Voltage: 4.5 to 5.5V
- USB Voltage: 5V±0.25V
- Servo Input: 0 to 36V 
- Working Temperature: -40 to 85℃

Weight & Dimensions:
- Dimensions: 40 x 60 x 17.5mm
- Weight: 40g

Package1 Included: with NEO GPS
- 1 x V5 nano Flight Controller
- 2 x Dupont Cables 
- 1 x ADC6.6 Cable 
- 2 x I2C/CAN Cables 
- 1 x SBUS Signal Cable 
- 1 x RSSI Cable 
- 1 x DSM Signal Cable 
- 1 x ADC3.3 Cable 
- 1 x Debug Cable 
- 1 x Safety Switch + Cable 
- 1 x Voltage Current Cable 
- 1 x PW-Link Module + Cable 
- 1 x Power Suppl Module 
- 1 x 16GB Memory Card 
- 1 x I2C Expansion Board 
- 1 x TTL Board 
- 1 x NEO GPS
- 1 x GPS Bracket 

Package2 Included: without NEO GPS

- 1 x V5 nano Flight Controller
- 2 x Dupont Cables 
- 1 x ADC6.6 Cable 
- 2 x I2C/CAN Cables 
- 1 x SBUS Signal Cable 
- 1 x RSSI Cable 
- 1 x DSM Signal Cable 
- 1 x ADC3.3 Cable 
- 1 x Debug Cable 
- 1 x Safety Switch + Cable 
- 1 x Voltage Current Cable 
- 1 x PW-Link Module + Cable 
- 1 x Power Suppl Module 
- 1 x 16GB Memory Card 
- 1 x I2C Expansion Board 
- 1 x TTL Board


No related record found