Home>DIY RC Drone Accessories>Receiver>BETAFPV F4 1S 12A AIO Brushless Flight Controller Built-in SPI Frsky Receiver For Toothpick Drones

BETAFPV F4 1S 12A AIO Brushless Flight Controller Built-in SPI Frsky Receiver For Toothpick Drones Item NO.: F44149

Name: BETAFPV F4 1S 12A AIO Brushless Flight Controller Built-in SPI Frsky Receiver For Toothpick Drones
Brand: BETAFPV
SKU: F44149
Price: 38.43 USD
Availability: SoldOut

Write a Review

US$ 38.43

US$ 45.21 Save US$ 6.78 (15% Off)

Sold Out

Product Name	BETAFPV F4 1S 12A AIO Brushless Flight Controller Built-in SPI Frsky Receiver For Toothpick Drones
Item NO.	F44149
Weight	0.025 kg = 0.0551 lb = 0.8818 oz
Category	DIY RC Drone Accessories > Receiver
Brand	BETAFPV
Creation Time	2021-07-12

BETAFPV F4 1S 12A AIO Brushless Flight Controller Built-in SPI Frsky Receiver For Toothpick Drones

F4 1S 12A AIO Flight Controller - A 1S 12A FC for building lightweight 3" toothpick drones like HX115 SE Toothpick Drone. If you want to try a bigger FPV drone than 65mm/75mm on 1S power, and still want smooth and powerful flying actions, this FC that integrates 1S 12A ESC is definitely your best choice.
Package
1 * F4 1S 12A AIO FC (Frsky)
4 * Anti-vibration rubber dampers
4 * M2 x 10mm screws
4 * M2 x 10mm screws
8 * M2 screw nut
Bullet Point
F4 1S 12A AIO Flight Controller is the best choice for building ultra-lightweight 3" toothpick drones like HX115 SE FPV Quad.
Most of 1S flight controllers on the market come with 5A ESC by now, but this FC especially integrates 1S 12A ESC, it can provide more sufficient power for 3" toothpick drones.
Built-in current meter, 2 programmable RGB LEDs, and SPI Frsky receiver. At the same time, all the pads are left for the external receivers with UART1 and UART2, for buzzers, etc.
Whoop mounting hole pattern, be compatible with most 1S 3" frame. Large pads are reserved for solder motor cables, this design will make solder easier.
Specification of FC
Item: F4 1S 12A AIO FC (Frsky)
Weight: 4.74 g (without power cable and BT2.0 connector)
CPU: STM32F411CEU6 (100MHZ )
Six-Axis: MPU6000 (SPI connection)
Firmware version: betaflight_4.2.0_STM32F411
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Receiver: Intergrated SPI Frsky Receiver / Futaba Receiver
Motor Pin Connecter: 1.25mm Header Pins
Mounting Hole Size: 29mm x 29mm (suitable for whoop pattern mounting hole)
USB Port: Type-C
Specification of 1S 12A ESC
Built-in ESC with 12A continuous and peak 25A current
Input voltage: 1S Lipo
ESC firmware: Z_H_30_REV16_7.HEX
Signal support: D-shot150, D- shot300, D-shot600, Oneshot125, Multishot, PWM
This new BLHeli_S firmware (named Z_H_30_REV16_7.HEX) is supported by BLHeli Configurator, BLHeliSuite, and Bluejay Configurator.
Diagram for F4 1S 12A AIO FC
UART1, UART2, and SBUS pads are left for external receivers like Frsky XM+, TBS Nano receiver so that a long receiver range is available.
Buzz pads (BUZZ+ and BUZZ-) are invalid directly. It needs some modification to make it works.
12A 1S ESC
Should we really need a 12A ESC for 1S drones? If it is a 65mm or 75mm Whoop drone like Meteor65, 5A ESC is enough for all actions. But how about with 3" propellers and 1102/1202.5 motors? Still want smooth and powerful flying actions? The 5A ESC has developed about 3 years ago and designed for whoop drones with 0603/0802 motors. For the past year, BETAFPV team has been cooperating with BLHeli author Steffen on the 12A 1S ESC for 3" toothpick drones. Finally, it is here!
It marks "1-2S" on the board, could this FC board support 2S?

NOT Yet. The motor spins not smoothly in 2S power with the released ESC firmware. We will work on it continuously and make this board support 2S later. If you have any ideas or advice, feel free to contact us.

SPI Frsky RX
Come with the build-in SPI Frsky Receiver (CC2500 chip), F4 1S 12A AIO FC can be compatible with Futaba S-FHSS, Frsky D8, and D16 protocol. The default protocol is configured to Frsky D16 FCC out of the factory. Pilots could set up the protocol according to your own need in Betaflight Configurator.
Configuration
Protocol
FRSKY_D
Frsky D8
FRSKY_X
Frsky D16 FCC (ACCST 1.X version)
FRSKY_X_LBT
Frsky D16 LBT (ACCST 1.X version)
SFHSS
Futaba S-FHSS
How to Bind with Betaflight FC with SPI Frsky Receiver.
Recommend Parts
BNF: highly recommend for HX115 SE Toothpick Drone
Battery: BT2.0 300mAh 1S 30C Battery / BT2.0 450mAh 1S 30C Battery / PH2.0 300mAh 1S 30C Battery
Motor: 1102 18000KV motor
Propeller: HQ3020 2-blade props