iFlight SucceX F4 TwinG Flight Controller + SucceX 50A ESC 2-6s BLHeli_32 Dshot1200 4-in-1 Flytower Flight Tower for FPV Racing Drone Quadcopter DIY Models

Copy and share this link on social network or send it to your friends

Copy

iFlight SucceX F4 TwinG Flight Controller + SucceX 50A ESC 2-6s BLHeli_32 Dshot1200 4-in-1 Flytower Flight Tower for FPV Racing Drone Quadcopter DIY Models Item NO: F28593

US$ 79.99
Remark:
Customized Requirements
Quantity:
Shipping Cost:
Free Shipping
  • iFlight SucceX F4 TwinG Flight Controller + SucceX 50A ESC 2-6s BLHeli_32 Dshot1200 4-in-1 Flytower Flight Tower for FPV Racing Drone Quadcopter DIY Models
Product Name iFlight SucceX F4 TwinG Flight Controller + SucceX 50A ESC 2-6s BLHeli_32 Dshot1200 4-in-1 Flytower Flight Tower for FPV Racing Drone Quadcopter DIY Models
Item NO F28593
Weight 0.0230 kg = 0.0507 lb = 0.8113 oz
Category DIY RC Drone Kit / RC Drone Accessories > Flight Control
Brand iFlight
Creation time 2019-04-23

iFlight SucceX F4 TwinG Flight Controller + SucceX 50A ESC 2-6s BLHeli_32 Dshot1200 4-in-1 Flytower Flight Tower for FPV Racing Drone Quadcopter DIY Models


Specifications :

FC Specifications
MCU:STM32F405R6T6
IMU:Twins IC2689,Twins Gyros built-in(SPI)
Baro:BMP280
OSD:AT7456E
Blackbox:Blackbox logging device
5X Uarts(1 2 3 4 5)with build-in inversion
8X Dshot/Proshot/Oneshot output
8X individual ESC power/ signal pads
1X Group of Gnd/Vbat/M1/M2/M3/M4/Cur/TX
Smart audio & Tramp VTX protocol:YES(IRC Tramp)
WS2812 led Strip:YES
Beeper:YES
PDB Specifications
Input:2-6S(5-36V)
BEC:5V/3A cont
 
 
FC Firmware
Betaflight/INAV
Target:STM32F405
FC:IFRC/IFF4_TWIN_G(STM32F405)
 
 
Physical
Mounting:30.5*30.5mm,φ4mm with Grommets φ3mm
Dimensions:36*36mm
Weight:6.3g
SucceX 50A 2-6S BLHeli_32 Dshot1200 4-in-1 ESC
 
 
Features:
8 layers double-sided PCB board;
4oz 1.6mm thick power board(0.9mm copper ratio),better operating load capacity;
32bit FO51K86 MCU, 48mHz maximum clock speed;
TDK MLCC Low ESR ceramic capacitors;
Top grade NTMFS5C430NL MOSFET;
Rational layout, countersunk holes on extended solder pads to ensure PCB layer connection
 
 
Specification:
Dimension: 43*39mm
Mounting Holes: 30.5*30.5mm/Φ3mm
Weight:14.4g
Supports 2-6S lipo input
STM32F051 MCU, 48Mhz Runs BLHELI 32.X Firmware
Current sensor: Yes
BEC: No
Supports: DShot DShot150/300/600/1200/MultiShot/ OneShot etc.
Target: iFlight-BL32-4IN1
 
 
RECOMMENDATION:
No additional capacitor needed up to 5S!
To encounter back EMF and ensure the longevity of your electronics, min. 220uF Cap 35V for 4-5S, 50V for 6S on your main lead!
 
 
Package included:
SucceX F4 TwinG FC+ SucceX 50A 2-6s BLHeli_32 Flytower

No related record found

You May Also Like