iFlight ProTek35 HD 151mm 3.5inch 4S CineWhoop BNF w BWhoop F7 45A AIO/XING 2205 3200KV Motor/3535 Prop for FPV Racing Drone

Description：

After our very popular 3inch Cinematic EVA bumper BumbleBee and Green Hornet CineWhoop series, we were trying to increase performance and reduce weight for an even better and longer flight experience for a wide variety of use. 

Our all new 3.5inch project is finally ready for all you content creators or those guys who like to wear some protection every now and then. Prop protection is what we're talking about here... 

ProTek is not necessarily just a Cinewhoop series but far more. Equipped with our all new 2205 3200KV motors for more power and less heat. We were able to increase speed and thrust by 50% compared to it's 3inch predecessor which gives a lot more room for a lot more fun. Our GPS measured maximum speed was above 120km/h and a maximum thrust of 750g per motor (3kg in total) would even carry heavier cams than a Gopro but also do some loaded punch outs or light freestyle moves. 

A lot of thought was put into the different assembly options. Our stock BNF will ship in the standard configuration but you can either do a pusher mod (flip the build upside down) or a lite mod (remove the protective plastic for weight optimization). 

Durable plastic protectors with copper standoffs, portable compact design, easy accessable UBS port without disassembly, LED battery status, lost model buzzer and a universal GoPro TPU for a full size or naked GoPro. If you wanna go extra light, get one of our 5V balance plug GoPro power cables to get rid of the internal battery. 

Features:

No Props or frame in view!

High performance True-AIO Board Beast Whoop F7 AIO 45A to save weight and space

T700 Quality Carbon (40% more tensile strength compared to common 3K carbon)

Lightweight one-piece frame design (Less flexibility, more Rigid, more Durable)

Low Resonance frame construction (Less Jello, more Cinematic footage)

DJI FPV Air Unit 720p 120fps FPV feed (record in 1080p/60fps)

Butter smooth 2205 3200KV (4S) motors

Pre-tuned with smooth freestyle settings

PRE-TUNED & PRE-SETUP:

Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!

To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"

Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!

Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode"

ProTek35 BNF Specs:

Board Beast Whoop F7 AIO 45A

Motor: XING 2205 3200KV (4S) 

Wheelbase: 151mm

Body Size: 118*94.5mmmm

Bottom plate thickness: 3.5mm

Top plate thickness: 2mm

Top and bottom plate spacing: 20mm (aluminum standoff height) 

Propeller size: 3.5 inch

FC pattern: 25.5*25.5mm / 20*20mmmm

FPV cam spacing: 20mm

Weight: 348.3g (without battery)

ProTek35 HD Quad BNF Included Components and Parts

pre-built and tested Quadcopter

1x ProTek35 Frame

1x DJI FPV Camera

1x DJI FPV Air Unit Module

2x DJI FPV Air Unit Antenna SMA

1x TPU Bracket for DJI Air Unit Module

1x TPU Antenna holder for DJI antenna

2x TPU camera side plate soft mount

2x Nazgul 3535 propeller (Set of 4 - Color May Vary)

1x iFlight Lipo Strap 15*150mm (Color May Vary)

1x  iFlight Lipo Strap 15*250mm (Color May Vary)

FC // Beast F7 AIO

Specification:

MCU: BGA-STM32F745

Gyro: MPU6000

Blackbox: 8Mb Onboard Flash

BEC output: 5V 2.5A 

Barometer: BMP280

Connector: Micro-USB

OSD: AT7456E

FC Firmware：IFLIGHT_F745_AIO 

Mounting pattern: 25.5*25.5mm φ3mm

Dimensions: 32.5*32.5mm

Weight: 8.5g

ESC // 45A 2-4S

Specification:

Uarts: 5

Current Sensor: Yes

Input: 2-4S LIPO

Current scale: 200

Constant: 45A / Burst: 50A

BLHeli: BLHeli-S

Telemetry: no

ESC Firmware: BlheliS G-H-30

Mounting pattern: 25.5*25.5mm/Φ3mm

Dimensions: 32.5*32.5mm

Recommendation of battery

Fullsend 4S 95C 1300mAh

Additional Suggested Parts（donot include）

DJI HD FPV Goggles

Radio Controller

DJI Remote Controller (Mode 2)

Important

The DJI Remote Controller is recommended for beginners since you won't need to set up another receiver, but it is also optional in this BNF drone because it is NOT required in order to use the FPV system. If you don't choose to use the DJI Remote Controller, you can choose a receiver option for your transmitter and then bind to your own radio as usual.