Product Name | iFlight BLITZ F7 45A 2-6S Stack W/ BLITZ F7 V1.1 Flight Controller / BLITZ E45S 4-IN-1 ESC / SucceX-Force 5.8g 800mW VTX for FPV |
Item NO. | F47257 F47258 |
Weight | 0.1 kg = 0.2205 lb = 3.5274 oz |
Category | DIY RC Drone Accessories |
Brand | iFlight |
Creation Time | 2022-06-16 |
Description:
FC // BLITZ F7 V1.1 Flight Controller
Top Features:
Improved circuit design, better components and lower electrical noise!
DJI HD VTX Connector (Plug-and-Play / No soldering required)
FC indicator LEDs for visual debugging
With LC filter
Specifications:
MCU: STM32 F722
Gyro: BMI270
Barometer: DPS310
OSD Chip: AT7456E
Flash: 32MB (Blackbox flash)
UARTS: 6
Motor outputs: 4x (SH1.0 connector)
I2C serial: SDA / SLA pads
Smartaudio / IRC Tramp VTX protocol supported
LED controller: Yes
Beeper pad: Yes
Firmware target: IFRC-IFLIGHT_BLITZ_F722
Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter
Dimensions: 36.5*35 mm
Weight: 7.8g
Wiring suggestion:
UART 1 for VTX HD / Analog
UART 2 for a Receiver
UART 3/4/5 for GPS or other sensors that require a serial port
UART 6 for ESC Telemetry
Tips
1. F722 MCU has an inner inverter.
2. SBUS、CRSF、ELRS、IBUS、DSM ETC... can be connected to any unused UART_RX,we suggest you connect to Uart_RX2
3. Frsky SmartPort,Tramp & Smartaudio can be connected to any unused UART_TX,we suggest you connect to Uart_TX1
4. F.port can be connected to any unused UART_TX,we suggest you connect to Uart_TX2
ESC // BLITZ E45S 4-IN-1 2-6S ESC
Specification:
Supports: DShot150/300/600/MultiShot/ OneShot etc.
Mounting Holes: 30.5*30.5mm/Φ4mm
Supports 2-6S lipo input
Telemetry Output: NO
Target: QH-40 16.7
Current sensor: Yes
Constant: 45 Amps
Current rate: 200
Burst: 55 Amps
Weight: 14.7g
MCU: BB21
BEC: NO
VTX // SucceX Force 5.8GHz 800mW VTX Adjustable
Features:
Stable output power
5 Power levels up to 800mW;
48 Channels (including Raceband)
Fast frequency lock, no startup interference with other pilots
Built-in output power self-check functionality
VTX telemetry with IRC Tramp protocol
Tips:
VTX is set to 25mW by default! Power levels above 25mW require a HAM license or have to be approved by local authorities! Please ensure you're flying legal frequencies and use our prepared Betaflight VTX tables according to your region.
Specs:
Input voltage: 7V~36V (@12V/380mA@800mW)
Video standard: NTSC /PAL
Output voltage/ Max current: 5V 1A
Power levels: PIT/25mW/100mW/400mW/800mW
Power draw @12V input current: 40mA@PIT MODE, 95mA@25mW, 185mA@100mW,250mA@400mW, 380mA@800mW
Channels: 48 (including Raceband)
Small size: 36*36*3mm
Mounting pattern: 30.5x30.5 (4x M3)
Lightweight: 7.5g (excluding antenna)
VTX telemetry: IRC Tramp
Betaflight IRC Tramp Configuration: Please download the attached VTX table for Betaflight!
All our VTX tables can also be found here: LINK
IRC Tramp VTX table values: 25/25mW, 100/100mW, 400/400mW, 600/800mW
PACKAGE INCLUDED:
1PC X BLITZ F7 V1.1 FLIGHT CONTROLLER
1PC X BLITZ E45S 4-IN-1 2-6S ESC
1PC XSucceX Force 5.8GHz 800mW VTX Adjustable
1SET X SILICON GROMMETS
1SET X WIRE HARNESS FOR F7 FLIGHT CONTROLLER
SKYPE: +8615012643826
Email:yxy@xt-xinte.com
No related record found