XT-XINTE 2.5 /3.5 USB 3.0 to 2 SATA Ports 1 IDE Port External HDD Hard Drive Disk Docking Station Card Reader USB3.0 Hub with OTB/OTC Item NO.: F31976 F31977

XT-XINTE 2.5"/3.5" USB 3.0 to 2 SATA Ports 1 IDE Port External HDD Hard Drive Disk Docking Station Card Reader USB3.0 Hub with OTB/OTC

Color: black red

Size: 140*130*66mm

Weight: 600g

feature:

The hard disk offline clones copy, one-key backup, you can also clone the A disk data to the B disk C disk without connecting to the computer. Suitable for high-definition movies, system copy and other workers, can connect 3 SATA hard drives at the same time, support up to 6TB capacity hard drive, output USB2.0 interface, users can choose interface transmission according to their actual needs. Whether you are an advertising practitioner, a film editor, or a photography enthusiast, maybe you are a high-definition movie enthusiast or a web BT downloader, you can easily back up, share your information, and share it easily with friends and colleagues. You don't need to bring a computer, just connect your large-capacity hard drive, and then chat for a while, you can take all the information you want!

 

product manual:

Product Name: Three Slots SATA HDD Holder Supports Offline Cloning

Support hard disk: 2.5 inch / 3.5 SATA (serial port) hard disk

IDE/SATA hard drive three-digit design

USB3.0 supports USB2.0.USB1.1 up and down

Supports all 2.5" and 3.5" SATA I and SATA II interface hard drives

2 USB2.0 expansion interfaces

Compatible with USB3.0, SATA I, SATA II, SATA III

Built-in high-speed multi-function card reader

Flash card interface: SD/TF/CF/XD/MS

Plug and Play / Hot Plug

Power input: 100~240V, 50/60Hz,

Power output: 12V-3A

Button function: offline cloning and one-click backup

Supported hard drives: 2.5/ 3.5-inch SATA hard drive

Support card class: SD/Extreme SD/Extreme III SD/Ultra II SD/MMC/RSMMC

Support card: MS/MS DUO/MS PRO, etc.

Support card class: TF

Support card class: CF I/CF II/Extreme CF/HS CF/MD

Support card class: XD

Support system: Win98SE, 2000, ME, XP, Mac OS 9.x or higher

       

Instructions for use:

1. Before the hard disk is cloned, just connect the power supply, the power is off, and you can't connect the USB to the computer at this time.

2. Please note that the capacity of the A disk (master disk) must be less than or equal to the capacity of the B disk (sub disk).

3. After the hard disk is completely connected, turn on the power switch, please wait for five seconds. After the hard disk is fully started, press the clone button (square red button). At this time, the indicator light is half bright, indicating that the cloner is ready for processing. Press the clone button again within 3 seconds (for example, if the clone button is not pressed within 3 seconds, the system will return to the power-on state, indicating that the red light is off), the indicator light will flash rapidly, and the system is cloning data, please wait until When the red light stops flashing, the clone is completed. At this time, please turn off the power first. After the hard disk is completely stopped, you can remove the hard disk. Precautions:

1. The capacity of the target hard disk must be greater than or equal to the capacity of the source hard disk, because the copy is a whole disk copy.

2. Once the copy starts, all the data on the target hard disk will be formatted, so please pay attention to the data on the target hard disk before copying.

3. It may take a long time to copy the action. Please be patient and the LED does not stop flashing. Please do not turn off the power or remove the hard disk at will!

4. The time of copying the entire hard disk depends on the capacity of the source hard disk, regardless of the size of the actual data file in the source hard disk.

5. If the capacity of the source hard disk is 120G, calculate the 60M/S (3600M/min) with the copy speed of SATA2. The formula is: 120G×1024/3600=about 34 minutes (the above is the estimated time for the actual measurement, depending on the environment) set)

6. If the B disk is larger than the A disk, for example, A is 80G and B is 120G. After the clone is completed, the B disk will be displayed as about 40G unpartitioned on the computer. Please partition it in the disk manager to use it.

7.USB and ESATA can not be used at the same time. When USB is connected to the computer, the hard disk of the two slots can be recognized at the same time. When the ESATA is connected to the computer, only one disk can be recognized.

The product contains:

Host*1

USB cable*1

Power adapter (12V/3A)*1

Instruction manual*1