JMT DIY FPV Racing Drone Quadcopter F4 Pro V2 Flight Control 180mm Carbon Fiber Frame with RunCam Micro Swift 3 Camera BNF No TX

JMT DIY FPV Racing Drone Quadcopter F4 Pro V2 Flight Control 180mm Carbon Fiber Frame with RunCam Micro Swift 3 Camera BNF No TX Item NO: F26776-C

US$ 128.96 (15% Off)
US$ 151.72 Save US$ 22.76
Remark:
Customized Requirements
Quantity:
Shipping Cost:
Estimate Shipping Cost
  • JMT DIY FPV Racing Drone Quadcopter F4 Pro V2 Flight Control 180mm Carbon Fiber Frame with RunCam Micro Swift 3 Camera BNF No TX
Product Name JMT DIY FPV Racing Drone Quadcopter F4 Pro V2 Flight Control 180mm Carbon Fiber Frame with RunCam Micro Swift 3 Camera BNF No TX
Item NO F26776-C
Weight 1.0400 kg = 2.2928 lb = 36.6849 oz
Category DIY RC Drone Kit / RC Drone Accessories > DIY RC Drone Kit
Brand JMT
Creation time 2018-12-15

JMT DIY FPV Racing Drone Quadcopter F4 Pro V2 Flight Control 180mm Carbon Fiber Frame with RunCam Micro Swift 3 Camera BNF No TX

The drone will come Assembled, Bind and Fly

Package include:

1xFeichao 180mm Frame Kit

2x2204-2300KV CW Motor

2x2204-2300KV CCW Motor

1xBS430 4 in 1 ESC 30A 3-6S

1x20CM anti-fastening strap

1xUltra-small Buzzer

1xRunCam Micro Swift 3 Camera

1x5.8G 25/200/600MW 7086 48CH Image Wireless Video Transmission

1xFrsky D16 Receiver

1x11.1V 1500MAH 40C XT60 Battery

1xBattery Charger

1x4pcs/set 3M Ultralight Shakeproof Sponge

4x4050 Props (Red)

1xXT60 Connect Cable

1xPagoda3 antenna

1xbetaflight OmniF4 Pro(V2) Flight Controller


Wheelbase: 180mm

Weight: 73g
Arm thickness: 3mm
Upper and lower plate thickness: 1.5mm
Flight control mounting hole size: 27mm x 27mm to 30.5mm x 30.5mm
Support motor: 2204, 2205, 2305, 2306

Frame size Wheelbase: 180mm
Weight 695g (before assembly)
Flight time is about 10min
Flight Control / ESC betaflight OmniF4 Pro (V2) flight control / 30A 3-6S 4 in 1 BLHeli-S firmware Dshot ESC
Motor 2204 2300KV
Blade 4045 three-bladed paddle
Figure 5.8G 25/200/600MW 7086 48CH picture transmission TL300N6
Camera RunCam Micro Swift 3 Micro Swift 600TVL 2.1mm (M12) 165 degrees FPV aerial camera through the camera PAL system
Battery / Power 11.1V 1500MAH 40C
Product Features "1. The aircraft has rise, fall, hover, forward, backward, left turn, right turn, left fly, right fly, self-stable, semi-stable, buzzer in the air. All have been set), (manual mode (for new hands) and other modes need to be set by yourself).
2. The aircraft fuselage is made of high-strength and low-weight carbon fiber board, which is resistant to falling and durable.
 3. We have debugged and calibrated the flight control and ESC. It is no longer necessary to make complicated settings for the flight control, and it can be assembled simply by flying.
                                                                                                                         1. Can your rack be used with other motors and ESCs? Can the paddle be changed? a: Of course, we recommend motor 2300kv-2400kv, ESC 20A-35A, paddle 4 inch 

2. Can I use a larger capacity battery? 

a: Our ESC support voltage is 3-6s, the recommended maximum capacity is 2200mah. The battery is 3S
   "
Flight Control Assistant Software: Betaflight Official website address :https://github.com/betaflight/betaflight-configurator
Precautions "
1. When using the charger, do not charge the charger with 2S and 3S batteries at the same time.
2. Do not modify any parameters and wiring without knowing the flight control and remote control.
3. Turn on the remote control before powering the aircraft. After the flight is over, unplug the power supply and turn off the remote control to prevent accidents.
4. This aircraft is not recommended to fly indoors. It is recommended to fly in an open space to avoid flying in places where people and disturbances are present. "





No related record found