jmt JMT 2018 New Betaflight 3.2.5 Firmware CC3D Flight Controller with Shell Case for DIY FPV RC Multirotor Drone Racing Multicopter
JMT 2018 New Betaflight 3.2.5 Firmware CC3D Flight Controller with Shell Case for DIY FPV RC Multirotor Drone Racing Multicopter

JMT 2018 New Betaflight 3.2.5 Firmware CC3D Flight Controller with Shell Case for DIY FPV RC Multirotor Drone Racing Multicopter Item NO: F24806-F24807

US$ 6.26 (15% Off)
US$ 7.36 Save US$ 1.10
Type:
Straight Pin Bent Pin
Shipping Cost:
Estimate Shipping Cost
Quantity:
Specifications
Product Name JMT 2018 New Betaflight 3.2.5 Firmware CC3D Flight Controller with Shell Case for DIY FPV RC Multirotor Drone Racing Multicopter
Item NO F24806-F24807
Weight 0.0600 Kg
Category DIY RC Drone Kit / RC Drone Accessories
Brand jmt
Creation time 2018-05-09

Detail

JMT 2018 New CC3D-RAID Betaflight 3.2.5 Firmware CC3D Flight Controller with Shell Case for DIY FPV RC Multirotor Drone Racing Multicopter

Straight Pin and Bent Pin 2 Versions are optional
The CC3D-RAID Board comes with Yellow Shell Case

Product specification
With Shell Case size: 40mm*40mm*14mm
With Shell Case weight: 15.2g
Board size: 36mm*36mm
Net weight: 7.3g
CC3D-RAID Comes from the original CC3D chip, optimizes the PCB layout and replaces the more advanced gyroscopes;
It changes the inconvenience of the original Mirco USB port;
The new CC3D uses Betaflight ground station and firmware and parameter settings, which is simpler than the original Openpilot.
Perfect function, suitable for beginners, easier for experienced players.
Its function is stronger than ordinary F3.
Note: This flight controller does not support Openpilot firmware. Only Betaflight firmware and debugging software are supported.

The OpenPilot Copter Control 3D aka CC3D is a board more tuned to Acrobatic flying or GPS based auto-piloting. It only has one sensor, The MPU6500(Fast SPI) based Acc/Gyro. It also features a 16Mbit SPI based EEPROM chip. It has 6 ports labeled as inputs (one pin each) and 6 ports labeled as motor/servo outputs (3 pins each).

If issues are found with this board please report via the github issue tracker.

The board has a USB port directly connected to the processor. Other boards like the Naze and Flip32 have an on-board USB to uart adapter which connect to the processor's serial port instead.

The board cannot currently be used for hexacopters/octocopters.

Tricopter & Airplane support is untested, please report success or failure if you try it.

Pinouts

The 8 pin RC_Input connector has the following pinouts when used in RX_PPM/RX_SERIAL mode

Pin

Function

Notes

1

Ground

2

+5V

3

Unused

4

SoftSerial1 TX / Sonar trigger

5

SoftSerial1 RX / Sonar Echo / RSSI_ADC

Used either for SOFTSERIAL, SONAR or RSSI_ADC*. Only one feature can be enabled at any time.

6

Current

Enable feature CURRENT_METER. Connect to the output of a current sensor, 0v-3.3v input

7

Battery Voltage sensor

Enable feature VBAT. Connect to main battery using a voltage divider, 0v-3.3v input

8

PPM Input

Enable feature RX_PPM

*Connect to the output of a PWM-RSSI conditioner, 0v-3.3v input.

The 6 pin RC_Output connector has the following pinouts when used in RX_PPM/RX_SERIAL mode

Pin

Function

Notes

1

MOTOR 1

2

MOTOR 2

3

MOTOR 3

4

MOTOR 4

5

LED Strip

6

Unused

The 8 pin RC_Input connector has the following pinouts when used in RX_PARALLEL_PWM mode

Pin

Function

Notes

1

Ground

2

+5V

3

Unused

4

CH1

5

CH2

6

CH3

7

CH4/Battery Voltage sensor

CH4 if battery voltage sensor is disabled

8

CH5/CH4

CH4 if battery voltage monitor is enabled

The 6 pin RC_Output connector has the following pinouts when used in RX_PARALLEL_PWM mode

Pin

Function

Notes

1

MOTOR 1

2

MOTOR 2

3

MOTOR 3

4

MOTOR 4

5

Unused

6

Unused

Serial Ports

Value

Identifier

Board Markings

Notes

1

VCP

USB PORT

2

USART1

MAIN PORT

Connected to an MCU controllable inverter

3

USART3

FLEX PORT

4

SoftSerial

RC connector

Pins 4 and 5 (Tx and Rx respectively)

The SoftSerial port is not available when RX_PARALLEL_PWM is used. The transmission data rate is limited to 19200 baud.

To connect the GUI to the flight controller you just need a USB cable to use the Virtual Com Port (VCP) or you can use UART1 (Main Port).

CLI access is only available via the VCP by default.

Main Port

The main port has MSP support enabled on it by default.

The main port is connected to an inverter which is automatically enabled as required. For example, if the main port is used for SBus Serial RX then an external inverter is not required.

Flex Port

The flex port will be enabled in I2C mode unless USART3 is used. You can connect external I2C sensors and displays to this port.

You cannot use USART3 and I2C at the same time.

Flex port pinout

Pin

Signal

Notes

1

GND

2

VCC unregulated

3

I2C SCL / UART3 TX

3.3v level

4

I2C SDA / UART3 RX

3.3v level (5v tolerant

No related record found

You May Also Like