Product Name | IFlight Taurus X8 Pro HD BLITZ F7 Pro 80A DJI Air Unit XING2 3110 8S 8inch FPV Cinelifter Drone for DSLR Red Komodo ZcamBMPCC |
Item NO. | F47042-D1 F47042-D2 |
Weight | 5.2 kg = 11.4640 lb = 183.4246 oz |
Category | DIY RC Drone Accessories > DIY RC Drone Kit |
Brand | iFlight |
Creation Time | 2022-04-27 |
Engineered with professionals for professionals, a BNF that's aimed for carrying
big payloads offering a soft-damped universal platform for DSLR or
cinema cameras (Red Komodo, Zcam, BMPCC, etc) featuring DJI's FPV HD
transmission system. 8-single X-Class grade ESCs for maximum reliability
and power. Redundancy is a big safety
factor when carrying expensive cinema gear. Even in case of an overload
or failure, the remaining ESCs and motors will be able to carry your
gear back to you. In case you get troubles with signal interference or
radio signal loss the GPS rescue feature will automatically take over
control, climb to max flight altitude, fly back in a straight line, and
descend towards your liftoff location until the signal transmission is
regained (no automated landing). The integrated TPU landing gear
provides sufficient height for most terrain and offers some protection
on harder landings.
Test data:
Flight time with 5.000mAh 8S:
- No camera installed: 12min
- Installed camera: 6-8min
Maximum speed:
- Low payload: 160km/h
- High payload: 130km/h
Payload:
- Maximum payload: 2kg
- Recommended payload: 1-1.5kg
Features:
Big size XING2 3110 // The power motors with extreme lift and flight performance
8S power system // More power and speed
8x single X-Class grade ESC motor drivers for more reliability
Redundant iFlight ESC Commander PCB // Power distribution board with high capacitance, filtering and heat dissipation
GPS module pre-installed (BF GPS rescue or INAV GPS RTH feature available)
Universal camera mount and accessories for a wide range of cameras to install
PRE-TUNED & PRE-SETUP:
Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!
Angle-Mode (self-balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!
To restore lost tunes or updates, please check our linked article on"Firmware/Factory Dumps"
GPS Rescue is ON by default.Please check our linked article on"GPS Rescue Mode // Setup"
Please check our linked article on"How to disable Angle-Mode, activate Acro-Mode"
Taurus X8 Pro BNF Specs:
GPS module: iFlight M8Q-5883-GPS & Compass V2.0
Total Dimensions: 430mm*350mm (body dimension)
Upper(middle) plate thickness: 3.5mm
Weight: 2.3kg±5g (without battery)
Bottom plate thickness: 3.5mm
BLITZ F7 Pro Flight Controller
Motor: XING2 3110 900KV
Top plate thickness: 3mm
Arm Thickness: 8mm
Propeller size: 8 inch
Wheelbase: 450mm
FC // BLITZ F7 Pro Flight Controller
Mount pattern: 35*35mm / 4mm PCB hole diameter
Smart audio / IRC Tramp VTX protocol supported
Firmware target: IFLIGHT_BLITZ_F7_PRO
BlackBox: 512MB Onboard
Dimensions: 41*41.5mm
BEC: 5V/2.5A, 12V/2A
Barometer: DPS310
OSD Chip: AT7456E
LED controller: Yes
MCU: STM32 F722
Weight: 17g (±2)
Beeper pad: Yes
Gyro: MPU6000
UARTS: 6
ESC // 2 x iFlight ESC Commander PCB (8x SucceX X80A)
Supports up to Dshot600, Proshot, Oneshot, Multishot
Firmware Target: iFlight-BL32-PRO
Up to 48kHz PWM frequency
Mounting pattern: 40*17mm
Constant: 80A / Burst: 100A
Capacitance: 470uF/35V
BlHeli32 telemetry: Yes
Current Sensor: Yes
Input: 2-8S LIPO
Weight:8.1g
MCU: F051
BEC: No
Taurus X8 Pro HD BNF Included Components and Parts
8 x HQ 8X4X3 CW propeller + 8 x HQ 8X4X3 CW propeller (Color may vary)
2 x Albatross LHCP 5.8GHz SMA FPV Antenna
1 x XT90 Male to XT60 Female Adapter Wire
2 x iFlight Lipo Strap 20*400mm (Black)
2 x iFlight Lipo Strap 20*500mm (Black)
1 x Pre-built and Tested Taurus X8 Pro
1 x DJI FPV Air Unit Module + Camera
1 x CNC Aluminum alloy cam mount
1 x XT90 Smart Smoke Stopper
1 x Prop Wrench
Important
The
DJI Remote Controller is recommended for beginners since you won't need
to set up another receiver, but it is also optional in this BNF drone
because it is NOT required in order to use the FPV system. If you don't
choose to use the DJI Remote Controller, you can choose a receiver
option for your transmitter and then bind to your own radio as usual.
Note:
All iFlight BNFs are tested before shipment to guarantee the highest quality.
If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.
SKYPE: +8615012643826
Email:yxy@xt-xinte.com
No related record found