IFlight Taurus X8 HD SucceX-D F7 BLHELIS 80A M8Q-5883 FPV Air Unit XING 2806.5 1300KV 6S 8inch FPV Cinelifter Drone
Let's introduce our new iFlight Taurus X8 BNF, our heavy duty gear to lift those big cams!
Engineered with professionals for professionals, a BNF that's aimed for carrying big payloads offering a soft-damped universal platform for DSLR or cinema cameras (Red Komodo, Zcam, BMPCC, etc) featuring DJI's FPV HD transmission system. Redundant ESC and motor setup for maximum performance but also a safety factor. Even in case of an overload or failure, one remaining ESC and 4 motors will be able to carry your expensive camera back to you. In case you get troubles with signal interference, radio signal loss, or complete FPV transmission fail the GPS rescue feature will automatically take over control, climb to max flight altitude, and descent towards your liftoff location until the signal transmission is regained (no automated landing). The integrated TPU landing gear provides sufficient height for most terrain and offers some protection on harder landings.
2kg maximum payload for a variety of top-mounted cameras and the ability to fine-adjust the stable mount for a perfectly balanced CG (Center of Gravity). The underslung battery acts as a power source as well as a counterweight to strategically slide the weight more front or back to counter camera lenses of different weight or length. The adjustable CNC aluminum mount offers angles from 5 to 35 degrees and can be safely secured for reproducible outcomes. No jello, no jitter, no problem; Our silicon-ball dampened carbon camera base is decoupled from the rest of the frame to reduce the amount of vibration generated by motors and propellers. For the perfect cinematic shot we recommend and additional software stabilization in the post or a hardware module (for example SteadXP).
The estimated flight time with 6S 4500mAh and attached cinema camera is about 4-6min, depending on speed and wind conditions! (set includes one battery)
Features:
XING 2806.5 efficient and powerful wide stator motors
Redundant ESC and motor configuration
Stable silicon-ball decoupled camera CNC mount
GPS flight data and rescue functionality
2kg max payload for various cinema and DSLR cameras
Optimized CG through the adjustable camera and battery mount
Taurus X8 BNF Specs:
SucceX-D F7 TwinG V2.1 Stack (LINK)
Motor: XING 2806.5 1300KV (LINK)
GPS module: iFlight M8Q-5883-GPS & Compass V2.0 (LINK)
Wheelbase: 400mm
Body Size: 283*283mmmm
Top and bottom plate spacing: 20-31mm (aluminum standoff height)
Propeller size: 8 inch
Weight: 1574.4g (without battery)
FC // SucceX-D F7 TwinG V2.1
MCU: 216MHz STM32F722
Gyro:2x ICM20689
Barometer: YES
Blackbox:32MB
Betaflight OSD: YES
BEC: 5V 2.5A / 9V 2.5A
UARTs: 5
Input voltage: Recommended 2-6S, MAX 8S
Firmware Target: IFLIGHT_F722_TWING
Mounting pattern: 30.5*30.5mm φ4mm with Grommets φ3mm
Dimensions: 36*36mm
Weight: 7.5g
USB type-C
ESC // 2x SucceX 80A 2-8S 4in1
MCU: STM32F051
Up to 48kHz PWM frequency
Capacitance: 470uF/50V
Current Sensor: Yes
Input: 2-8S LIPO
Constant: 80A / Burst: 100A
BlHeli32 telemetry: Yes
BEC: No
Supports up to Dshot600, Proshot, Oneshot, Multishot
Firmware Target: iFlight-BL32-4IN1
Weight:18.6g
Mounting pattern: 30.5*30.5mm/Φ3mm
Taurus X8 HD BNF Included Components and Parts
pre-built and tested Taurus X8
1 x Taurus X8 Frame
1 x Fullsend X 6S 70C 4400mAh
1 x DJI FPV Air Unit Module + Camera
4 x Albatross LHCP 5.8GHz SMA FPV Antenna
8 x HQ 8X4X3 propeller (Set of 2- Color May Vary)
2 x iFlight Lipo Strap 20*300mm (Black)
1 x Prop Wrench
Important
The DJI Remote Controller is recommended for beginners since you won't need to set up another receiver, but it is also optional in this BNF drone because it is NOT required in order to use the FPV system. If you don't choose to use the DJI Remote Controller, you can choose a receiver option for your transmitter and then bind to your own radio as usual.
No related record found