Home>DIY RC Drone Accessories>Frame>FEICHAO F4-V2 178mm Quadcopter DIY Drone Kit BNF RTF 25A 4IN1 ESC F4 OSD Flight Controller 1204 5000KV Motors FLYSKY/T-lite Radio
FEICHAO F4-V2 178mm Quadcopter DIY Drone Kit BNF RTF 25A 4IN1 ESC F4 OSD Flight Controller 1204 5000KV Motors FLYSKY/T-lite Radio

FEICHAO F4-V2 178mm Quadcopter DIY Drone Kit BNF RTF 25A 4IN1 ESC F4 OSD Flight Controller 1204 5000KV Motors FLYSKY/T-lite Radio Item NO.: F43623-B C D E F G H I J K

Write a Review
US$ 94.34
US$ 110.99 Save US$ 16.65 (15% Off)
Sold Out

Copy and share this link on social network or send it to your friends

Copy
Product Name FEICHAO F4-V2 178mm Quadcopter DIY Drone Kit BNF RTF 25A 4IN1 ESC F4 OSD Flight Controller 1204 5000KV Motors FLYSKY/T-lite Radio
Item NO. F43623-B C D E F G H I J K
Weight 0.418 kg = 0.9215 lb = 14.7445 oz
Category DIY RC Drone Accessories > Frame
Brand FEICHAO
Creation Time 2021-05-08

FEICHAO F4-V2 178mm Quadcopter DIY Drone Kit BNF RTF 25A 4IN1 ESC F4 OSD Flight Controller 1204 5000KV Motors FLYSKY/T-lite Radio


Note: They are 10 versions, pls choose the corresponding version according to the picture.


Functions and features

178mm wheelbase
Built-in OSD Betaflight
Support BLHeliSuit configuration
Maximum support battery 3S
Battery life is about 7 minutes
The remote control distance (with FLYSKY remote control) is about 400 meters, (with T lite remote control) is about 2000 meters

Paddle

Product Name: 4032
Propeller pitch: 3.2 inch wheels
Hub size: 5mm
Weight: 3.09g
Material: PC
Center thickness: 6.5 mm
Propeller diameter: 102.2mm


Flight control and ESC integration

Product name: Integrated 25A 4 in 1 ESC F4 OSD flight controller
Size: 32.5x32.5mm
Mounting hole: 25.5x25.5mm
Weight: 7.3 grams
CPU: STM32F411CEU6 (100MHZ)
Firmware: Betaflight JHEF411
Integrated OSD Betaflight (AT7456E)
BEC output (two): 9V / 2A, 5V2.5A
Receiver: SBUS, IBUS, DSM2, DSMX, TBS (UART2)
Black box: 8MB
Built-in current sensor
Support WS2812 LED
Input voltage: 2-6S Lipo
ESC current: 25a / 35A
Firmware: BLHELI_S GH-30.HEX
Support PWM, Oneshot42, Oneshot125, Multishot, Dshot150 and Dshot300, Dshot600


Image Transmission

Project name: 5.8G 40CH 25mW 100mW 200mW switchable FPV transmitter
Input voltage: 4.5-5.2V (DC)
Input current: 500mA @ 200mW
Power: 25mW / 100mW / 200mW (switchable)
Channel: 40CH
Antenna connector: IPEX
Size: 37x24x5mm
Mounting hole: 25x25mm
Weight: 2g


Motor

KV: 2400
Stator diameter: 18mm
Motor weight: 16g (without cable)
Power supply voltage: 2-3s
Maximum current: 6.5A
Maximum power: 70W"

Camera

Lens: 1.8mm
Aspect ratio: 16:9
Resolution: 1200TVL
Input voltage: DC3.7V-18V
Weight: 2g
Installation size: 14mm/19mm


Receiver version:

FRSKY version, FLYSKY version, without receiving version


Note:

1 Do not charge the battery when you are away from home, do not charge the battery immediately after flying, and do not over-discharge the battery (over-discharge may cause the battery to fail to charge and become useless). The battery cannot be powered off in time after it is fully charged. Charge for a long time.
2. Do not modify any parameters and wiring without knowing the flight control and remote control.
3. Turn on the remote control before powering on the aircraft, unplug the power switch after the flight, and then close the remote control to prevent accidents.
4. This product is not a toy and is not suitable for children under 14 years of age.
5. If you are a beginner, it is recommended to be assisted by an experienced adult
6. Novices should pay attention not to take the airplane by hand when the airplane is turning or let children take it to prevent it from being scratched
7. Please turn off the start switch in time when the aircraft falls from a high altitude or hits other objects during flight, otherwise it may cause damage to the flight control motor, etc. Check whether the aircraft is damaged or the screws are loosened, etc. before taking off again when everything is normal.



No related record found