Home>DIY RC Drone Accessories>Flight Control>BETAFPV Upgrade Lite Brushed Flight Controller Compatible with Sliverware Firmware Version for Small BWhoop Quadcopter

BETAFPV Upgrade Lite Brushed Flight Controller Compatible with Sliverware Firmware Version for Small BWhoop Quadcopter Item NO.: F36044

Name: BETAFPV Upgrade Lite Brushed Flight Controller Compatible with Sliverware Firmware Version for Small BWhoop Quadcopter
Brand: BETAFPV
SKU: F36044
Price: 16.14 USD
Availability: SoldOut

Write a Review Sold (10)

US$ 16.14

US$ 18.99 Save US$ 2.85 (15% Off)

Sold Out

Product Name	BETAFPV Upgrade Lite Brushed Flight Controller Compatible with Sliverware Firmware Version for Small BWhoop Quadcopter
Item NO.	F36044
Weight	0.038 kg = 0.0838 lb = 1.3404 oz
Category	DIY RC Drone Accessories > Flight Control
Brand	BETAFPV
Creation Time	2020-03-09

BETAFPV Upgrade Lite Brushed Flight Controller Compatible with Sliverware Firmware Version for Small BWhoop Quadcopter
· Integrate 25 mW VTX, support change VTX brand channel via control.

· Add Lite OSD information and OSD Menu.

· Support firmware update in DFU mode via USB port.

· Integrate an altitude sensor (altitude maintenance function is NOT available now).

2 RGB LEDs

Features
The world's first FC firmware compatible Silverware card. This must be the easiest and most convenient method to look for whoop FPV racing hobbies.
Support level and acro mode mode. It also has the ability to change settings for custom builds, or to adapt to personal preferences from stick gestures.
Designed to work with Small Whoop Current or Lama Inductrix Frames
Built in Bayang native protocol receiver, compatible with almost radio transmitter with firmware deviation or compatible transmitter module deviation
The flight controller board comes pre-flashed with firmware silverware, and pre-soldered 55mm pigtail power cord with JST-PH 2.0 connector, AKA PowerWhoop connector.

Specifications
CPU: STM32F042
Six-Axis: MPU6050
ESC: All Fetes are rated at 6.3A maximum. Support 6x1 5mm / 7x2 0mm / 8x2 0mm / 8.5x20mm, etc. motors.
Dimensions: 26mm x 26mm, fully compatible with the Inductrix quad frame and mounting model
Firmware version: Silverware firmware
Receiver: Bayang protocol
Power cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 2.5g
Silverware & LiteOSD
Silverware is a firmware for some micro quadcopters, which support level and acro mode mode. So that you can use this on whoop FPV racing. It also has the ability to change settings for custom builds, or to adapt to personal preferences.

LiteOSD is also integrated into the V2 board. So that you could configure many configrations based on your preferences easily. The method of entering the OSD Menu on Lite Brushed FC is the same as Betaflight. Make sure the drone is disarmed when entering OSD Menu on Lite 1 S Brushless FC.

Supported Radio Transmitter
Currently the built-in receiver is compatible with the Bayang protocol. Here is a list of radio transmitter that could be compatible with this FC board.

LiteRadio Transmitter
BETAFPV LiteModule RF module (with PA, range> 300 m, suit for Frsky Tanaris QX7 X9D X9D Plus X12S, Flysky TH9X, Turnigy 9XR / 9XR PRO)
Toy drone radio transmitter like JJRC H67, Eachine E011, etc., which uses Bayang protocol
Jumper T8SG radio transmitter
MTX-9D multi-protocol module
Other 4in1 multiprotocol module supporting the Bayang protocol
If you are unsure if your radio transmitter could support this FC board, please email us (info@betafpv.com) for help.

For example, if you have a Frsky Tanaris QX7 / X9D radio transmitter and want to try this FC board, just connect a BETAFPV LiteModule RF and done.

Some drivers would complain that it is definitely not a long FC series. The signal is lost with my transmitter far too often and for what appears to be no reason. This problem is often caused by the location of the antenna. You should keep the antenna away from the FC edge to get a stronger signal. For example, singal upwards. Thanks for Harley Finberg's advice.

Frames and display items
1 * BETAFPV Lite brushed flight controller V2.0
4 * M1.2x4mm screws (Fit for stock Inductrix frame)
4 * M1.4x5mm screws (Fit for Beta75 etc. 75mm frame)

4 * Anti-vibration ruber shock absorbers